44
EN
incorrect installation.
On bikes with 130-135 mm (5,1 -5,3 inch) chainstay you
must insert the right chainstay adapter (Ref. D) (Pic. 9) ) and
the left adapter (E) (Pic. 10). However, on bikes with ø12 mm
(ø 0.47 inches) thru-axle and 142 mm (5,6 inches) chainstay
please check paragraph 17.
16_INSTALLING THE BICYCLE ON SUITO
- Loosen the bike’s rear brake and place the chain on
the smallest rear sprocket and the largest front chainring.
Remove the quick release from the rear wheel.
- Remove the rear wheel from the bicycle.
- Insert the quick release and the dropout adapter (Ref. C) on
the Suito sprocket cassette (Pic. 14).
- Place the bicycle chain onto the smallest sprocket of Suito
(Pic 15).
- Fully fit the bicycle’s rear dropouts onto Suito’s cassette
(Pic. 16), paying careful attention to the correct internal or
external position, based on the type of bicycle:
- External triangle adapter (Ref. C) for road and time trial bikes
(130mm triangle) (Pic.17).
- Internal triangle adapter (C) for mountain bikes (135mm
triangle) (Pic. 18).
NOTE: the knurled side of the triangle adapter (Ref. C) must
be facing the bicycle dropout.
- Securely fix the bicycle to Suito and firmly close the quick
release. The resulting pressure should keep the bicycle
dropouts locked to the Suito.
- Make sure the bike is perfectly vertical once installed.
WARNING: the dropout of the bicycle must be leaning on the
edges of the adapter and not on the Quick Release.
Elite shall not be liable for any damages that might arise from
an improper assembly of the bicycle on the hometrainer.
17_INSTALLING THE SUITO ON BICYCLES
WITH Ø12 L=142 MM CHAINSTAYS
1) Insert the left and right adapters (Ref. F - G) for 142mm
chainstays (Pic. 16);
2) Loosen the rear brake of the bicycle and place the chain
on the smallest sprocket of the rear wheel and the front
chainring. Remove the thru-axle from the rear wheel.
3) Position the bicycle’s rear dropouts on the axle of the
sprocket cassette of the Suito.
4) Insert the thru-axle on the Suito sprocket cassette shaft.
5) Make sure the bicycle is safely positioned on the Suito and
lock the thru-axle with a strong push. The pressure should
make the bike dropouts remain locked onto the structure of
the Suito.
6) Make sure the bike is stable by pushing and pulling the
top tube of the frame and the saddle. Should the bike still
be moving a little on the Suito, use more force to lock the
thru-axle.
7) If you wish for more bicycle stability it's advisable to use the
provided Riser block (Ref I) to be placed under the front wheel.
- Start pedalling. Ride very slowly at first and increase your
speed gradually until you become familiar with the features of
Suito.
18_POWER SUPPLY
- Suito feature electronic circuitry inside and is powered up by
a standard power supply (included).
Insert the power supply in the electrical outlet and the jack
plug in the connector on the back of the Suito (Pic. 17), a
slight vibration indicates that the system is adjusting to its
initial position. This can last up to 15 seconds.
Place the cable inside its housing in the rear of the
hometrainer and hook it in the edges in the lower area of the
rear plastics (pic. 18)
The Suito compliance with EU laws (see “Declaration of
conformity”, page 112) may be voided if a charger different
from the original is used.
19_REMOVING THE BICYCLE
- Shift the bicycle chain on the smallest cassette sprocket of
Suito and of the smallest front chainring of the bicycle.
- Open up the quick release (or remove the thru-axle) and
remove the bicycle from the Suito.
- For transportation or to reduce clutter when not using the
hometrainer: Raise the selectors (Pic. 19) and fold the side
legs (Pic. 20 - 21).
WARNING: the adapters ref. C, D, E, F, G are small sized
components and might easily be misplaced or lost. If you
move the hometrainer it's advisable to remove the adapters
and store them in their bag as they might easily slip out during
transport.
Any spare parts are available in our online store or by directly
contacting Elite and/or your country's distributor.
20_INSTALLATION OF CAMPAGNOLO
®
9/10/11 SPEED COMPATIBLE CASSETTE
FREEHUB BODY
- To replace the original freehub body installed on Suito with
the accessory body compatible with Campagnolo
®
9/10/11
speed cassettes, follow the procedure below:
1) Remove the cassette pre-assembled on the hometrainer
( Pic 22 )
2) Unscrew the fastening sleeve (Pic 23).
3) Remove the freehub body from the Suito shaft (Pic. 24).
4) Fully insert the Campagnolo
®
cassette compatible freehub
body (Pic. 25-26).
5) Tighten the fastening sleeve with a 17 straddle wrench
Summary of Contents for SUITO
