Elektro-Automatik EA-PSI 10000 3U Series, Manual

Page: 2 / 96

© EA Elektro-Automatik in 2022, this information is subject to change without notice 2 06230820_manual_psi_10000_3u_15kw_en_01
TABLE OF CONTENTS
1. General
1.1 About this document 4
1.1.1 Retention and use 4
1.1.2 Copyright 4
1.1.3 Validity 4
1.1.4 Symbols and warnings 4
1.2 Warranty 4
1.3 Limitation of liability 4
1.4 Disposal of equipment 5
1.5 Product key 5
1.6 Intended usage 6
1.6.1 Symbols and warnings on the device 6
1.7 Safety 7
1.7.1 Safety notices 7
1.7.2 Responsibility of the operator 8
1.7.3 Requirements to the user 8
1.7.4 Responsibility of the user 8
1.7.5 Alarm signals 9
1.7.6 Functionality test 9
1.8 Technical data 10
1.8.1 Approved operating conditions 10
1.8.2 General technical data 10
1.8.3 Specific technical data 11
1.8.4 Views 16
1.8.5 Control elements 19
1.9 Construction and function 20
1.9.1 General description 20
1.9.2 Block diagram 20
1.9.3 Scope of delivery 21
1.9.4 Accessories 21
1.9.5 Options 21
1.9.6 The control panel (HMI) 22
1.9.7 USB port (rear side) 25
1.9.8 Interface module slot 25
1.9.9 Analog interface 25
1.9.10 “Share BUS” connector 26
1.9.11 “Sense” connector (remote sensing) 26
1.9.12 Master-Slave bus 26
1.9.13 Ethernet port 27
2. Installation & commissioning
2.1 Transport and storage 28
2.1.1 Transport 28
2.1.2 Packaging 28
2.1.3 Storage 28
2.2 Unpacking and visual check 28
2.3 Installation 28
2.3.1 Safety procedures before installation and use 28
2.3.2 Preparation 28
2.3.3 Installing the device 29
2.3.4 Connection to AC supply 30
2.3.5 Connection to DC loads 33
2.3.6 Connection of remote sense 35
2.3.7 Grounding of the DC output 36
2.3.8 Installation of an interface module 36
2.3.9 Connecting the analog interface 37
2.3.10 Connecting the Share bus 37
2.3.11 Connecting the USB port (rear side) 37
2.3.12 Initial commission 37
2.3.13 Commission after a firmware update or a long
period of non-use 37
3. Operation and application
3.1 Personal safety 38
3.2 Operating modes 38
3.2.1 Voltage regulation / Constant voltage 38
3.2.2 Current regulation / constant current / current
limiting 39
3.2.3 Power regulation / constant power / power
limiting 39
3.2.4 Internal resistance regulation 40
3.3 Alarm conditions 41
3.3.1 Power Fail 41
3.3.2 Overtemperature 41
3.3.3 Overvoltage protection 41
3.3.4 Overcurrent protection 41
3.3.5 Overpower protection 41
3.3.6 Safety OVP 42
3.3.7 Share bus fail 42
3.4 Manual operation 43
3.4.1 Switching on the device 43
3.4.2 Switching the device off 43
3.4.3 Configuration via the menu 43
3.4.4 Adjustment limits 51
3.4.5 Changing the operating mode 51
3.4.6 Manual adjustment of set values 52
3.4.7 Switching the DC output on or off 53
3.4.8 Recording to USB stick (logging) 53
3.4.9 The quick menu 54
3.4.10 The graph 55
3.5 Remote control 56
3.5.1 General 56
3.5.2 Control locations 56
3.5.3 Remote control via a digital interface 56
3.5.4 Remote control via the analog interface 58
3.6 Alarms and monitoring 62
3.6.1 Definition of terms 62