Electrolux EDW 1100 Service Manual Download Page 52

Page: 52 / 56

9.2.1. Overview Errors Displayed

Applicable for EDW1500 / 1503 (VGA) -- EDW1100 / 1003 (VGA) -- EDW2000

Error
Name

Display

Screen

Display

END LED

Acoustic

Indication

No.of Beeps

Error Display

visible for

Customer**

Call

Error Memory

(Service)

Output via

Indicator Lamp

Short Explanation

What happens?

2Hz / 5sec. Pause

Display

PAA

Display

PAA

EDW 1500

EDW1100

If available for

this model

If available for

this model

Water tap closed

1 x
flashing

1 x

LED Water

Switchpoint of pressostat is not reached

after max. 60 secs.

(only in programme steps incl. Filling up to level!)

Programme stops and can be continued after error remedy by

pressing the programme key. If fault is not corrected and programme

key is pressed, the machine runs dry until next subprogramme.

Drain pump

2 x
flashing

2 x

---

Reset point of pressostat is not reached after max. 120secs.

Programme stop.

Programme stops and can be continued after error remedy

by pressing the programme key.

Aqua-Control

3 x
flashing

3 x

---

Aqua-Control System switches off solenoid directly.

Programme stops and restarts automatically when error has

terminated.

Recycling pump
Triac short-circuit

5 x
flashing

5 x

---

Tacho signals are recognized although rec. pump is not

selected.

Programme stops and water is filled up until reset point of

pressostat

Heating

6 x
flashing

6 x

---

During heating, temperature rise by min. 1.5K is not detected

within 3min.

Programme is continued until its end without heating function!

NTC Sensor

7 x
flashing

7 x

---

NTC short-circuit or break.

Programme is continued until its end without heating function!

EEPROM

8 x
flashing

8 x

---

Communication error with ext. EEPROM

Check sum
MCF / CCF

9 x
flashing

9 x

---

Check sum (model programming) MCF or Check sum CCF

not OK.

Only recognized after switching on!

Programme selection not possible.

On/Off LED is on

Sprayarm blocked

10 x
flashing

10 x

LED Spray arm

At programme start and each subprogramme start,

also after door open/close or mains failure, spray arm

rotation

is checked and evaluated.

Error display until sprayarm speed is recognized,

or if no control.

Turpidity sensor

11 x
flashing

11 x

---

The turbidity signal required for calibration

is not reached with 15secs.

Always recognition of turbidity.

Programme sequence is adapted accordingly.

Communication
error

12 x
flashing

12 x

---

Communication failure with User Interface.

Machine stops, waiting until communication is cleared.

Tacho

13 x
flashing

13 x

---

Recycling pump selected, but no tacho signal

recognized for 5 + 20 secs

Recycling pump without control, heating off.

This function is checked again on each step.

Filling time error

14 x
flashing

14 x

---

Time limit during filling exceeded

Programme is completed until next subprogramme without

level. No further filling up of water top up. Error is reset after

one complete drain cycle.

= If 7-Segment display available, no PAA error display/Sound error display generally with VGA, with other machines depending on model

DGN-TDS-N

Summary of Contents for EDW 1100

























































Search results

Summary of Contents for EDW 1100

Reviews:

Related manuals for EDW 1100

Brands by name

Popular brands

Electrolux EDW 1100, Service Manual

Search results

Summary of Contents for EDW 1100

Reviews:

Related manuals for EDW 1100

Brands by name

Popular brands