Electrolux EDW 1100 Service Manual Download Page 40 | Manualshive

Page: 40 / 56

background image

8.4.1. Accessing the service menu

So that the service menu can be called up, the dishwasher must be switched off!
The button lock is also not to be activated.

1.

Ä

Press the Option and Ok/Start buttons at the same time and ....

2.

Ä

...to this end, switch the dishwasher on with the On/Off button.

Ä

The Service Menu is activated!

The selection can only be reset by switching the dishwasher off.

The two buttons Option and Ok/Start must be kept pressed in until the
text "1 ERROR CODE i" appears in the text line after the word
"HALLO".

The selection of individual menu items in the service menu is
described in detail on the following pages.

If no selection is made in the service menu, the
setting automatically returns to the initial selection
after a pre-determined time (Time out).

1.

OPTION

OK/START

EIN/AUS

OPTION

OK/START

EIN/AUS

Servicemenü ist aktiviert!

2.

«
...
38
39
40
41
42
...
»

Summary of Contents for EDW 1100

























































Reviews:

No comments

Related manuals for EDW 1100

Spacemaker DSKS333EC

Brand: GE Pages: 3

FDW-VRR606BDE++

Brand: FRAM Pages: 42

Brand: ZANKER Pages: 48

Brand: Zanussi Electrolux Pages: 16

Brand: CLEANVAC Pages: 8

Brand: Hotpoint Pages: 20

Brand: Blomberg Pages: 44

Brand: Kuppersberg Pages: 96

Brand: Hotpoint Pages: 20

Brand: V-ZUG Pages: 60

XQG50-QF800 - 07-01

Brand: Haier Pages: 24

Brand: Haier Pages: 28

Brand: Samsung Pages: 14

Brand: Samsung Pages: 80

Brand: Samsung Pages: 56

Brand: Samsung Pages: 60

Brand: Samsung Pages: 68

Brand: Samsung Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands