Electrolux E15IM60GPS, Service Manual

Page: 6 / 47

6
Installation / General Instructions
Adjusting Door Alignment
1. Loosen (do not remove) top and bottom
hinge screws (Figures 9 and 10) .
15
Adjusting Door Alignment
1. Loosen (do not remove) top and bottom hinge screws
(Figure 11 and Figure 12) .
Figure 11
Figure 12
2. Align door squarely with cabinet. Make sure gasket is
firmly in contact with cabinet all the way around the
door (no gaps).
3. Tighten bottom hinge screws.
4. Tighten top hinge screws.
Checking Drawer Alignment
The unit’s drawers are aligned at the factory before
shipment. However, their alignment could have been
disturbed during shipment or during overlay panel
installation.
Figure 13
See Figure 13 . Check each drawer to confirm that it is
aligned:
• Side-to-Side — When viewed from the top, the
drawer front should be square with the sides of the
cabinet.
• Front-to-Back — When viewed from the side, the
drawer front should be straight with the cabinet’s
sides, not cocked forward or back.
•
Top-to-Bottom
— When viewed from the front, the
drawer should be level horizontally.
If both drawers are properly aligned, no further
adjustment is necessary. If either drawer is not aligned,
carefully follow instructions to remove that drawer, make
the necessary adjustment and re-install the drawer.
ULIN_0293_A
ULIN_0104_A
7 Adjust Drawer
Aligned
Side-to-Side
Aligned
Front-to-Back
Aligned
Top-to-Bottom ULIN_0312_A
Figure 9
15
Adjusting Door Alignment
1. Loosen (do not remove) top and bottom hinge screws
(Figure 11
and
Figure 12)
.
Figure 11
Figure 12
2. Align door squarely with cabinet. Make sure gasket is
firmly in contact with cabinet all the way around the
door (no gaps).
3. Tighten bottom hinge screws.
4. Tighten top hinge screws.
Checking Drawer Alignment
The unit’s drawers are aligned at the factory before
shipment. However, their alignment could have been
disturbed during shipment or during overlay panel
installation.
Figure 13
See Figure 13 . Check each drawer to confirm that it is
aligned:
• Side-to-Side — When viewed from the top, the
drawer front should be square with the sides of the
cabinet.
• Front-to-Back — When viewed from the side, the
drawer front should be straight with the cabinet’s
sides, not cocked forward or back.
• Top-to-Bottom — When viewed from the front, the
drawer should be level horizontally.
If both drawers are properly aligned, no further
adjustment is necessary. If either drawer is not aligned,
carefully follow instructions to remove that drawer, make
the necessary adjustment and re-install the drawer.
ULIN_0293_A
ULIN_0104_A
7 Adjust Drawer
Aligned
Side-to-Side
Aligned
Front-to-Back
Aligned
Top-to-Bottom ULIN_0312_A
Figure 10
2.
Align door squarely with cabinet. Make sure
gasket is firmly in contact with cabinet all the
way around the door (no gaps).
3. Tighten bottom hinge screws.
4. Tighten top hinge screws.
Keypad Options
WARNING
Electrocution can cause death or serious
injury. Take precautions when touching a
bare circuit board. Wear an anti-static wrist
strap and ground it to an electrical ground or
grounded water pipe. Handle circuit boards
carefully and avoid touching components.
When touching key combinations in which
you hold one key and press another key three
times, it is important to carefullt follow this
procedure:
1. Hold the desired key ensuring the light above
the key is lit.
2.
Press the other key three times, ensuring it
lights up each time.
3. Release the held key only after releasing the
pressed key for the third time.
Except as noted, these functions are available
on all models.
ON/OFF
The ON/OFF mode allows the unit to be turned
on and off via the keypad. To do this, hold the key
for approximately 10 seconds until the “F” begins
to flash. Release the key and the unit will switch
modes.
This mode does not disconnect power from the
circuit board si it is still “LIVE”. Turning the unit off
while in
Clean
,
Ice Maker Off
,
Forced Harvest
,
or
Forced Defrost
will cancel those modes. If this
mode is entered while the unit is in an ice-making
harvest mode, it will continue it’s cycle and flash
“OFF” until completed.
Showroom Mode
This mode is designed to show units in a display
environment. When in this mode the only functions
will be the controls and cabinet lights. The
compressor, fans, etc. will not operate. To enter this
mode, hold the down arrow and press the LIGHT
button three times. When entered, the unit will beep
once and the degree symbol will be to flash. When
the degree symbol is flashing the unit will allow
the use of the control for demonstrations. After not
touching the unit for one minute the display will
begin to “snake” around. This is meant to alert you
the unit is in showroom mode. The unit can be left
in this mode indefinitely. If you again want to demo