Electrolux E15IM60GPS, Service Manual

Page: 5 / 47

5
Installation
13
Checking Door Alignment -
Échelon Models
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during door panel installation.
IMPORTANT IMPORTANT
Properly aligned, the door should be 1/8" below the
top of the unit’s cabinet, NOT flush with the top
(Figure 5).
Figure 5
1. Compare the top edge of the door to the top edge of
the cabinet.
2. If the door edge is 1/8" below and parallel to the top of
the cabinet, it is adjusted correctly. If it is not, note
whether the side opposite the hinge needs to be moved
UP or DOWN, and use the following procedure.
Échelon Full Overlay
NOTE: If door is adjusted correctly, but panel is not square
with the adjacent cabinets, slight adjustments can be
made by drilling the holes in the vinyl-coated steel panel
slightly oversized
(Figure 6)
.
Figure 6
Adjusting Door Alignment
1. Remove top hinge screw pin using a Phillips
screwdriver (Figure 7) . Remove door by tilting
forward and lifting off bottom hinge pin.
Figure 7
2. With door upside-down, loosen but do not remove the
two screws on the door’s bottom hinge plate.
6 Adjust Door
1/8"
ULIN_0295_A
Drill 5/32" x 3/8" Deep for use
with #10 x 5/8" Wood Screw
and Nylon Spacer – 6 Places
1"
±
1/8"
1"
±
1/32" 1"
±
1/32"
14-5/16"
±
1/4"
27"
±
1/4"
Rear View
of
Wood Panel
ULIN_0310_A
ULIN_0133_A
Figure 5
2
With door upside down, loosen but do not
remove the two screws on the door’s bottom
hinge plate.
3 See Figures 6 and 7.
If the top far edge of
the door needs to move UP, move the hinge
plate toward the outside of the door, then
retighten screws. If the top far edge of the
door needs to move DOWN, move the hinge
plate toward the inside of the dood, then
retighten screws.
14
Figure 8
3. See
Figure 8
and
Figure 9
. If the top far edge of the
door needs to move UP, move the hinge plate toward
the outside of the door and retighten screws. If the top
far edge of the door needs to move DOWN, move the
hinge plate toward the inside of the door and retighten
screws.
Figure 9
4. Mount the door to recheck alignment and repeat steps
2 and 3 if further adjustment is necessary.
5. When top edge of door is parallel to top edge of
cabinet, remove the door and ensure the two screws
are secure.
6. Remove the door closers from the bottom hinge, clean
thoroughly and lubricate the mating surfaces with
petroleum jelly.
7. Reinstall the closers, lining up the bosses with holes in
hinge and hinge plate (Figure 10) .
Figure 10
8. Mount the door, install top hinge pivot pin.
Checking Door Alignment -
Origins Models
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during door panel installation.
IMPORTANT IMPORTANT
Properly aligned, the door’s gasket should be firmly
in contact with the cabinet all the way around the
door (no gaps).
1. Carefully examine the door’s gasket to assure that it is
firmly in contact with the cabinet.
2. If the door is properly aligned, no further adjustment is
necessary. If it is not, use the following procedure.
Notch
Slotted
Mounting
Holes
Raise
Outside
Door Edge
Lower
Outside
Door Edge
ULIN_0297_A
Angled Edge
Towards Center
of Door
Slotted
Mounting
Holes
Raise
Outside
Door Edge
Lower
Outside
Door Edge
ULIN_0311_A
2115WC, 2115WCOL, 2175WC, 2175WCOL Only
Door
Closer
Inserts
Boss
ULIN_0298a_A
Figure 6
Adjusting Door Alignment
14
Figure 8
3. See
Figure 8
and
Figure 9
. If the top far edge of the
door needs to move UP, move the hinge plate toward
the outside of the door and retighten screws. If the top
far edge of the door needs to move DOWN, move the
hinge plate toward the inside of the door and retighten
screws.
Figure 9
4. Mount the door to recheck alignment and repeat steps
2 and 3 if further adjustment is necessary.
5. When top edge of door is parallel to top edge of
cabinet, remove the door and ensure the two screws
are secure.
6. Remove the door closers from the bottom hinge, clean
thoroughly and lubricate the mating surfaces with
petroleum jelly.
7. Reinstall the closers, lining up the bosses with holes in
hinge and hinge plate (Figure 10) .
Figure 10
8. Mount the door, install top hinge pivot pin.
Checking Door Alignment -
Origins Models
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during door panel installation.
IMPORTANT IMPORTANT
Properly aligned, the door’s gasket should be firmly
in contact with the cabinet all the way around the
door (no gaps).
1. Carefully examine the door’s gasket to assure that it is
firmly in contact with the cabinet.
2. If the door is properly aligned, no further adjustment is
necessary. If it is not, use the following procedure.
Notch
Slotted
Mounting
Holes
Raise
Outside
Door Edge
Lower
Outside
Door Edge
ULIN_0297_A
Angled Edge
Towards Center
of Door
Slotted
Mounting
Holes
Raise
Outside
Door Edge
Lower
Outside
Door Edge
ULIN_0311_A
2115WC, 2115WCOL, 2175WC, 2175WCOL Only
Door
Closer
Inserts
Boss
ULIN_0298a_A
Figure 7
1
Remove top
hinge screw pin
using a Phillips
serewdriver
(Figure 5)
.
Remove door by
tilting forward and
lifting off bottom
hinge pin.
4
Mount the door to recheck alignment and
repeat steps 2 and 3 if further adjustment is
necessary.
5
When top edge of door is parallel to top edge
of cabinet, remove the door and ensure the
two screws are secure.
6 Remove the door closers from the bottom
hinge, clean thoroughly and lubricate the
mating surfaces with petroleum jelly.
7
Reinstall the closers, lining up the bosses
with holes in hinge and hinge plate
(Figure
8)
.
14
Figure 8
3. See Figure 8 and Figure 9 . If the top far edge of the
door needs to move UP, move the hinge plate toward
the outside of the door and retighten screws. If the top
far edge of the door needs to move DOWN, move the
hinge plate toward the inside of the door and retighten
screws.
Figure 9
4. Mount the door to recheck alignment and repeat steps
2 and 3 if further adjustment is necessary.
5. When top edge of door is parallel to top edge of
cabinet, remove the door and ensure the two screws
are secure.
6. Remove the door closers from the bottom hinge, clean
thoroughly and lubricate the mating surfaces with
petroleum jelly.
7. Reinstall the closers, lining up the bosses with holes in
hinge and hinge plate
(Figure 10)
.
Figure 10
8. Mount the door, install top hinge pivot pin.
Checking Door Alignment -
Origins Models
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during door panel installation.
IMPORTANT IMPORTANT
Properly aligned, the door’s gasket should be firmly
in contact with the cabinet all the way around the
door (no gaps).
1. Carefully examine the door’s gasket to assure that it is
firmly in contact with the cabinet.
2. If the door is properly aligned, no further adjustment is
necessary. If it is not, use the following procedure.
Notch
Slotted
Mounting
Holes
Raise
Outside
Door Edge
Lower
Outside
Door Edge
ULIN_0297_A
Angled Edge
Towards Center
of Door
Slotted
Mounting
Holes
Raise
Outside
Door Edge
Lower
Outside
Door Edge
ULIN_0311_A
2115WC, 2115WCOL, 2175WC, 2175WCOL Only
Door
Closer
Inserts
Boss
ULIN_0298a_A
Figure 8
8 Mount the door and install top hinge pivot
pin.
Checking Door Alignment
The unit’s door is aligned at the foctory before
shipment. However, its alignment could have been
disturbed during shipment or during door panel
installation.
IMPORTANT
Properly aligned, the door’s gasket should be
firmly in contact with the cabinet all the way
around the door (no gaps).
1
Carefully examine the door’s gasket to
ensure that it is firmly in contact with the
cabinet.
2 If the door is properly aligned, no further
adjustment is necessary. If it is not, use the
following procedure: