ELECTRO FREEZE cs5, Operator'S Manual

Page: 22 / 62

ELECTRO FREEZE Model CS5
14
184627
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
8 Assembly -
continued
5. Insert the assembled beater into
the cylinder by sliding the beater shaft in
along the bottom of the cylinder. This will
center the beater shaft and allow align-
ment with the drive shaft. Rotate and
push the beater assembly until the shank
has engaged the drive shaft.
6. Install and lubricate the O-rings
(see O-ring chart) on the dispensing
plunger and insert into the head (figure
8-4).
7. Install and lubricate the 2½ inch
head O-ring.
8. Position the handle in the head
assembly and lock in place with the
handle pin.
9. Snap the nozzle on the mix outlet
at the bottom of the head.
Important:
Do not overtighten the hand knobs.
Excessive force will damage the head.
Tighten the hand knobs finger-tight
only.
10. Install the dispensing head onto
the freezer by sliding the head over the
threaded studs and aligning the square
end of the breaker bar with the square in
the dispensing head. Slide the head into
the cylinder and install the hand knobs,
being careful to tighten simultaneously
and finger-tight only.
NOTE: The plunger rod must be in place
for the freezer to operate in the “CLEAN”
or “AUTO” Mode.
11. Install the plunger rod.
12. Install the O-rings on the mix feed
tube and regulator as shown in figure 8-
5.
13. Lubricate the O-ring on the
regulator and install into the mix feed
tube. (No lubrication is required on the
mix feed tube O-rings.)
Figure 8-4 Assemble the head
assembly
Figure 8-5 Assemble the mix feed tube