Elation PROTHEUS HYBRID User Manual Download | Manualshive

Page: 38 / 48

background image

38

E R R O R C O D E S

Error Codes are subject to change without any prior written notice.

ERROR CODE

DESCRIPTION

PAN Er

The PAN movement is not located in the default position after the reset.
This message will appear after a fixture reset if the magnetic-indexing circuit

malfunctions (sensor failed or magnet is missing) or there is a motor failure
(defective motor or a defective motor IC drive on the main PCB). This error may
also be displayed if the head/yoke was blocked during a reset function.

TILT Er

The TILT movement is not located in the default position after the reset.
This message will appear after a fixture reset if the magnetic-indexing circuit
malfunctions (sensor failed or magnet is missing) or there is a motor failure
(defective motor or defective motor IC drive on main PCB). This error may also be

displayed if the head was blocked during a reset function.

Cyan

Wheel Er

The Cyan Color Wheel is not located in the default position after the reset.
This message will appear after the reset of the fixture reset if the magnetic-
indexing circuit malfunctions (sensor failed or magnet is missing) or there is a
stepper motor failure (defective motor or defective motor IC drive on main PCB).

Magenta

Wheel Er

The Magenta Color Wheel is not located in the default position after the reset. This
message will appear after the reset of the fixture reset if the magnetic-indexing

circuit malfunctions (sensor failed or magnet is missing) or there is a stepper
motor failure (defective motor or defective motor IC drive on main PCB).

Yellow

Wheel Er

The Yellow Color Wheel is not located in the default position after the reset.
This message will appear after the reset of the fixture reset if the magnetic-
indexing circuit malfunctions (sensor failed or magnet is missing) or there is a

stepper motor failure (defective motor or defective motor IC drive on main PCB).

Color

Wheel Er

The Color Wheel is not located in the default position after the reset.

This message will appear after the reset of the fixture reset if the magnetic-
indexing circuit malfunctions (sensor failed or magnet is missing) or there is a
stepper motor failure (defective motor or defective motor IC drive on main PCB).

CTO

Wheel Er

The CTO Color Wheel movement is not located in the default position after the
reset. This message will appear after a fixture reset if the gobo wheel’s magnetic-

indexing circuit malfunctions (sensor failed or magnet is missing) or there is a
stepper motor failure (defective motor or defective motor IC drive on main PCB).

Rotating Gobo

Wheel Er

The Rotating Gobo Wheel movement is not located in the default position after the
reset. This message will appear after a fixture reset if the gobo wheel’s magnetic-

indexing circuit malfunctions (sensor failed or magnet is missing) or there is a
stepper motor failure (defective motor or defective motor IC drive on main PCB).

«
...
36
37
38
39
40
...
»

Summary of Contents for PROTHEUS HYBRID

















































Reviews:

No comments

Related manuals for PROTHEUS HYBRID

Brand: Enigma Pages: 2

CitySkape Xtreme

Brand: Robe Pages: 24

Brand: Cameo Pages: 152

Brand: Mr. Beams Pages: 2

Brand: Varytec Pages: 28

Brand: Domus Pages: 4

Brand: Silver Star Pages: 18

STX2.50 Integral

Brand: Stoane Lighting Pages: 6

Brand: Stoane Lighting Pages: 6

Brand: Robus Pages: 2

Brand: Robus Pages: 2

Brand: Robus Pages: 3

Brand: Mr. Beams Pages: 3

Moving Head Spot

Brand: Hosen Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands