manualshive.com logo in svg

Elation PROTHEUS HYBRID, User Manual

Share
Download
Elation PROTHEUS HYBRID User Manual Download Page 40

 

40 

E R R O R   C O D E S 

Error Codes are subject to change without any prior written notice. 

ERROR CODE 

DESCRIPTION 

Animation Wheel Er 

The Animation Wheel movement is not located in the default position after the 
reset. This message will appear after a fixture reset if the magnetic-indexing circuit 

malfunctions (sensor failed or magnet is missing) or there is a motor failure 
(defective motor or a defective motor IC drive on the main PCB). This error may 
also be displayed if the head/yoke was blocked during a reset function. 

Dimmer Er 

The Dimmer movement is not located in the default position after the reset. 

This message will appear after a fixture reset if the magnetic-indexing circuit 
malfunctions (sensor failed or magnet is missing) or there is a motor failure 
(defective motor or defective motor IC drive on main PCB). This error may also be 
displayed if the head was blocked during a reset function. 

Frost 

Wheel Er 

The Frost Wheel is not located in the default position after the reset. 

This message will appear after the reset of the fixture reset if the magnetic-
indexing circuit malfunctions (sensor failed or magnet is missing) or there is a 
stepper motor failure (defective motor or defective motor IC drive on main PCB). 

Fan Moving 

Wheel Er 

The Fan Moving Wheel is not located in the default position after the reset. 
This message will appear after the reset of the fixture reset if the magnetic-

indexing circuit malfunctions (sensor failed or magnet is missing) or there is a 
stepper motor failure (defective motor or defective motor IC drive on main PCB). 

Array Lens 

Wheel Er 

The Array Lens Wheel is not located in the default position after the reset. 
This message will appear after the reset of the fixture reset if the magnetic-
indexing circuit malfunctions (sensor failed or magnet is missing) or there is a 

stepper motor failure (defective motor or defective motor IC drive on main PCB). 

1U_FanJB1Fault 

Error information from JB1 port on 1U01 PCB. 

1U_FanJB2Fault 

Error information from JB2 port on 1U01 PCB. 

3U_FanJB1Fault 

Error information from JB1 port on 3U PCB. 

3U_FanJB2Fault 

Error information from JB2 port on 3U PCB. 

4U_FanJB2Fault 

Error information from JB2 port on 4U PCB. 

5U_FanJB1Fault 

Error information from JB1 port on 5U PCB. 

6U_FanJB1Fault 

Error information from JB1 port on 6U PCB. 

7U_FanJB1Fault 

Error information from JB1 port on 7U PCB. 

7U_FanJB2Fault 

Error information from JB2 port on 7U PCB. 

7U_FanJB3Fault 

Error information from JB3 port on 7U PCB. 

Summary of Contents for PROTHEUS HYBRID

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands