Edwards PGC201 Instruction Manual Download Page 23

Page: 23 / 68

D0300040001EN - Installation

Page 13

Installation

Supplied equipment

Mechanical installation

The PGC201 can be used as follows:



Rack installation



Front panel installation



Benchtop instrument

Rack installation

The PGC201 has been designed for installation within a sub-rack (19 inches) in accordance
with DIN EN 60297 (IEC 60297) (see

Figure 2

). The equipment supplied includes four neck

collar screws and plastic sleeves for this purpose.

Table 8 Supplied equipment

Description

Quantity

PGC201

Mains cord with shockproof plug (EU)

Mains cord with shockproof plug (US)

Operating Instructions

Spare fuses

Neck collar screws

Plastic sleeves

Edge protection

Adhesive feet

WARNING:

Install the instrument or place it so that you are in a position to operate the mains power
switch at any time or ensure that the instrument can be de-energised at any time.

Summary of Contents for PGC201




































































Search results

Summary of Contents for PGC201

Reviews:

Related manuals for PGC201

Brands by name

Popular brands

Edwards PGC201, Instruction Manual

Search results

Summary of Contents for PGC201

Reviews:

Related manuals for PGC201

Brands by name

Popular brands