Edwards PGC201 Instruction Manual Download Page 13

Page: 13 / 68

D0300040001EN - Safety

Page 3

Safety

General information

The Edwards PGC201 controller is delivered ready for operation. This manual provides
installation, operation and maintenance instructions for the PGC201. The instrument must be
used as specified in this manual.

Key to the symbols

Important instructions relating to technical safety and safe operation are emphasised by
symbols.

Basic safety information

During all installation, maintenance and repair activities, comply with the pertinent safety
regulations.

WARNING:

Warnings are given where failure to observe the instruction could result in injury or death
to people.

CAUTION:

Cautions are given where failure to observe the instruction could result in damage to the
equipment, associated equipment and process.

WARNING:

Risk of electric shock.

Note:

General information pointing to further information, respectively reference sections.

WARNING:

Do not allow objects or liquids to enter the instrument. Coming into contact with
components at mains voltage level can be dangerous to life.

CAUTION:

Improper usage can damage the instrument. Use the instrument only in agreement with
the specifications issued by the manufacturer.

CAUTION:

Wrong connection and operating data can damage the instrument. Comply with all
specified connection and operating data.

Summary of Contents for PGC201




































































Search results

Summary of Contents for PGC201

Reviews:

Related manuals for PGC201

Brands by name

Popular brands

Edwards PGC201, Instruction Manual

Search results

Summary of Contents for PGC201

Reviews:

Related manuals for PGC201

Brands by name

Popular brands