Edwards iXL1000 Instruction Manual Download Page 69

Page: 69 / 70

Page 61

Edwards and the Edwards logo are trademarks of Edwards Limited.

Appendix A2

A540-55-880 Issue D

Example:

PDT shows the following:
0108 0200

This translates to:

alarm 1 in bit 2 – PWM_TRIP

alarm 8 in bit 4 – OVERT

warning 2 in bit 6 - HIGHTM.

This means the motor overheated and switched the output off.

HIGHTC

Controller temperature above upper limit / Controller
temperature sensor open circuit - check water supply

HIGHTS

Inverter heat sink temperature above upper limit /
Inverter heat sink temperature sensor open circuit - check
water supply

HIGHTM

Motor temperature above upper limit / Motor temperature
sensor open circuit - check water supply

MISSING_PHASE

The loss of one of the three input phases has been
detected - check mains supply to drive or blown fuses

UTCREG

Upper controller temperature regulator active - current
limit reduced - check cooling

UTSREG

Upper heat sink temperature regulator active - current
limit reduced - check cooling

UTMREG

Upper motor temperature regulator active - check motor
cooling

LVREG

Lower voltage regulator active - check mains voltage

LOWVCC

Internal power supply fault - contact Edwards

LOWTC

Low controller temperature - contact Edwards

LOWTS

Low heatsink temperature - contact Edwards

LOWTM

Low motor temperature - contact Edwards

Table A17 - Inverter warnings codes (continued)

Inverter warnings

BIT

Fault Code

Combination

Name

Description

Summary of Contents for iXL1000


































































Search results

Summary of Contents for iXL1000

Reviews:

Related manuals for iXL1000

Brands by name

Popular brands

Edwards iXL1000, Instruction Manual

Search results

Summary of Contents for iXL1000

Reviews:

Related manuals for iXL1000

Brands by name

Popular brands