EDT PCIe8g3 A5 10G User Manual Download Page 30 | Manualshive

Page: 30 / 48

background image

APPENDIX A: Registers for PCIe8g3 S5

Registers, Port: Ports 0–3 (SFPs)

EDT, Inc.

2017 January 04

30

Registers, Port: Ports 0–3 (SFPs)

0x800000–0x837FFF BAR1 Memory-Mapped

0x800000, 810000, 820000, 830000 Receive Framer Status and Control

0x800004, 810004, 820004, 830004 Receive Filter

Access / Notes:

32-bit read-write

0x800000 (Port 0): STRATIX5_REGXL8(STRATIX5_RX_FRM, 0)
0x810000 (Port 1): STRATIX5_REGXL8(STRATIX5_RX_FRM, 1)
0x820000 (Port 2): STRATIX5_REGXL8(STRATIX5_RX_FRM, 2)
0x830000 (Port 3): STRATIX5_REGXL8(STRATIX5_RX_FRM, 3)

Bit

Access

Name

Description

31

R only

[no name]

Copy of S5_RXFRM_BYTE_ALGND.

30–28

R only

[no name]

Byte offset.

27

R only

[no name]

Copy of S5_RXFRM_BIT_ALGND.

26–24

R only

[no name]

Bit offset.

23–16

–

–

Reserved.

15

R only

S5_RXFRM_FRM_
LCKD

When set, the framer has detected multiple consecutive frames and is locked.

14

R only

S5_RXFRM_FRM_
FOUND

When set, the framer has deteced the beginning of an SDH / OTN frame.

13–10

–

–

Reserved.

9

R only

S5_RXFRM_BYTE_
ALGND

When set, the framer is byte-aligned to the SDH / OTN frame alignment signal (FAS) pattern.

8

R only

S5_RXFRM_BIT_
ALGND

When set, the framer is bit-aligned to the SDH / OTN frame alignment signal (FAS) pattern.

7–5

–

–

Reserved.

4

RW

S5_RXFRM_DIS_
DSCRM

Set to disable the descrambler (i.e., acquire framed, scrambled data). Used only in conjunction with bit
1 (S5_RXFRM_EN).

3

RW

S5_RXFRM_CHK_
PAYLD

Set to enable hardware checking of PRBS payload data.

2

RW

S5_RXFRM_CAT_
PAYLD

Set to capture only payload data (i.e., strip framing).

1

RW

S5_RXFRM_EN

Set to allow data acquisition only when the framer is locked to the incoming signal. Acquired data is
descrambled.

0

RW

S5_RXFRM_RST

Reset framer. Set, then clear to force the framer to drop, then relock onto the framing pattern.

Access / Notes:

32-bit read-write
0x800004 (Port 0): STRATIX5_REGXL8(STRATIX5_RX_FILTER, 0)
0x810004 (Port 1): STRATIX5_REGXL8(STRATIX5_RX_FILTER, 1)
0x820004 (Port 2): STRATIX5_REGXL8(STRATIX5_RX_FILTER, 2)
0x830004 (Port 3): STRATIX5_REGXL8(STRATIX5_RX_FILTER, 3)

Bit

Access

Name

Description

31–8

–

–

Reserved.

7

RW

S5_RXFILT_IGNR_
ALL_FILT

Set to ignore all filters (overrides all other bits in this register).

«
...
28
29
30
31
32
...
»

Summary of Contents for PCIe8g3 A5 10G

















































Reviews:

No comments

Related manuals for PCIe8g3 A5 10G

Brand: Gallagher Pages: 11

Brand: LaCie Pages: 2

Brand: MosChip Pages: 3

Brand: TP-Link Pages: 2

Brand: Zonet Pages: 2

Pro AV 1600 PCI

Brand: Focus Pages: 24

Brand: Sminn Pages: 2

Brand: Compose Pages: 17

Brand: ICP DAS USA Pages: 6

GeForce 210 DDR3

Brand: EVGA Pages: 1

Brand: D-Link Pages: 42

Brand: Motorola Pages: 58

Brand: Motorola Pages: 50

Lava Parallel LAVA SP-PCIe

Brand: Lava Pages: 1

Brand: ANTAIRA Pages: 5

Brand: ACME Pages: 28

RocketPort EXPRESS

Brand: Comtrol Pages: 36

NuDAQ PCI-9812/10

Brand: ADLINK Technology Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands