background image

5

USING THE UNIT SAFELY

101b

• The unit and the AC adaptor should be 

located so their location or position does not 
interfere with their proper ventilation.

..................................................................................................

102c

• Always grasp only the plug on the AC 

adaptor cord when plugging into, or 
unplugging from, an outlet or this unit.

..................................................................................................

103b

• At regular intervals, you should unplug the 

AC adaptor and clean it by using a dry cloth 
to wipe all dust and other accumulations 
away from its prongs. Also, disconnect the 
power plug from the power outlet 
whenever the unit is to remain unused for 
an extended period of time. Any accumu-
lation of dust between the power plug and 
the power outlet can result in poor 
insulation and lead to fire.

..................................................................................................

104

• Try to prevent cords and cables from 

becoming entangled. Also, all cords and 
cables should be placed so they are out of 
the reach of children.

..................................................................................................

106

• Never climb on top of, nor place heavy 

objects on the unit.

..................................................................................................

107c

• Never handle the AC adaptor or its plugs 

with wet hands when plugging into, or 
unplugging from, an outlet or this unit.

..................................................................................................

108b

• Before moving the unit, disconnect the AC 

adaptor and all cords coming from external 
devices.

..................................................................................................

109b

• Before cleaning the unit, turn off the power 

and unplug the AC adaptor from the outlet 
(p. 21).

..................................................................................................

110b

• Whenever you suspect the possibility of 

lightning in your area, disconnect the AC 
adaptor from the outlet.

..................................................................................................

111

• If used improperly, batteries may explode 

or leak and cause damage or injury. In the 
interest of safety, please read and observe 
the following precautions (p.16).

1

• Carefully follow the installation instruc-

tions for batteries, and make sure you 
observe the correct polarity.

2

• Avoid using new batteries together with 

used ones. In addition, avoid mixing 
different types of batteries.

3

• Remove the batteries whenever the unit 

is to remain unused for an extended 
period of time.

5

• If a battery has leaked, use a soft piece of 

cloth or paper towel to wipe all 
remnants of the discharge from the 
battery compartment. Then install new 
batteries. To avoid inflammation of the 
skin, make sure that none of the battery 
discharge gets onto your hands or skin. 
Exercise the utmost caution so that none 
of the discharge gets near your eyes. 
Immediately rinse the affected area with 
running water if any of the discharge 
has entered the eyes.

6

• Never keep batteries together with 

metallic objects such as ballpoint pens, 
necklaces, hairpins, etc.

..................................................................................................

112

• Used batteries must be disposed of in 

compliance with whatever regulations for 
their safe disposal that may be observed in 
the region in which you live.

..................................................................................................

118c

• Should you remove ferrite cores, screws to 

fasten battery plate holder or screws 
removed from VC-50HD’s top panel, keep 
them in a safe place out of children’s reach, 
so there is no chance of them being swallowed 
accidentally.

..................................................................................................

Summary of Contents for VC-50HD SDI 1394






































Reviews: