Helios FM 20/100 W, user manual– 12/2011
Page 52
Head Office : Parc d’activites Kennedy - 20, avenue Neil Armstrong – F-33700 Bordeaux-Merignac (France)
Tel +33 (0)5 57 928 928 – Fax +33 (0)5 57 928 929 –
www.ecreso.com – [email protected]
NAME
Access
(R/W)
Possible value on the
serial port of the unit
Comments
INPUT.LINE2.FLT R/W
0;1;2
0=15;1=16;2=17 Configuration
of the audio filter
INPUT.LINE2.PREAC R/W 0;50;75 Sets the value of the pre-emphasis
INPUT.LINE2.LEVEL R/W
-20.00...18.00
Internal numerical gain. For AES, between -20 and
0; for ANA between -18 and +18
INPUT.PLAYER.LEFT.RMS
R
-100 … 28
Gives the left audio input average value
INPUT.PLAYER.LEFT.PEAK
R
-100 … 28
Gives the left audio input max peak value
INPUT.PLAYER.RIGHT.RMS
R
-100 … 28
Gives the right audio input average value
INPUT.PLAYER.RIGHT.PEAK
R
-100 … 28
Gives the right audio input max peak value
INPUT.PLAYER.PRESENCE
R
OFF or "L" or "R" or "L&R"
Indicates audio signals are present on the player
INPUT.PLAYER.SW.PRIO
R/W
0..4 ; 0=disabled
Priority of each audio channel (7= highest priority)
INPUT.PLAYER.SW.THRESH
R/W
-90…000
Silence triggering level in dBFS on channel 1
INPUT.PLAYER.SW.SILENCE R/W
"L" or "R" or "ANY" or
"BOTH"
Sets on which channel (L,R or L+R) silence
detection must be conducted for the audio input 1
INPUT.PLAYER.SW.BACKDEL
AY
R/W XXX=[0…30]
Back delay on the channel with the highest
configurable priority.
INPUT.PLAYER.SW.DELAY
R/W
XXX=[1…120]
Switching delay when loss of audio 1
INPUT.PLAYER.DRIVE
R/W
-6.00 to 6.00
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
INPUT.PLAYER.TRIM
R/W
-3.00 to 3.00
Sets the offset between left and right channels (+3 =
left channel level is 3 dBu higher than right channel
level)
INPUT.PLAYER.FLT R/W
0;1;2
0=15;1=16;2=17 Configuration
of the audio filter
INPUT.PLAYER.PREAC R/W
0;50;75 Sets the value of the pre-emphasis
INPUT.PLAYER.LEVEL R/W
-20...0
Internal numerical gain
INPUT.PLAYER.SAMPLING
R/W
"44" or "48" or "96"
Sampling frequency of the internal player audio
signal
INPUT.MPX.SW.THRESH R/W
-90…000 Silence triggering level in dBFS on MPX 1
INPUT.MPX.HWHPFLT
R/W
ON or OFF
Enables or disables the high pass hardware filter of
the integrated circuit PCM1804
INPUT.MPX.SW.BACKDELAY R/W
XXX=[0…30]
Back delay on the channel with the highest
configurable priority.
INPUT.MPX.SW.DELAY R/W XXX=[1…120]
Switching delay when loss on the MPX input
INPUT.MPX1.PRESENCE R
MO" or "MO+R" or
"MO+R+S" or "ST" or
"ST+R" or "ST+R+S"
Gives the composition of MPX1 on channel 3. R =
RDS ; MO = Mono ; ST = Stereo ; S = SCA
INPUT.MPX1.RMS R
-150…150
Gives the deviation average value of the transmitted
signal in kHz
INPUT.MPX1.PEAK R
-150…150
Gives the deviation max peak value of the
transmitted signal in kHz
INPUT.MPX1.SW.PRIO
R/W
0..7 ; 0=disabled
Priority of each audio channel (4= highest priority)
INPUT.MPX1.DRIVE
R/W
-6.00 to 6.00
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
INPUT.MPX1.TYPE R/W
"MO" or "ST" or "ST+R+S" or
"ST+R" or "RDS" or
"RDS+SCA" or "SCA"
Sets the type of signal on the MPX1 input and
applies the corresponding filter
INPUT.MPX1.LEVEL R/W
-18.00...+18.00
Internal numerical gain
INPUT.MPX2.PRESENCE R
MO" or "MO+R" or
"MO+R+S" or "ST" or
"ST+R" or "ST+R+S"
Gives the composition of MPX2 on channel 3. R =
RDS ; MO = Mono ; ST = Stereo ; S = SCA
INPUT.MPX2.RMS R
-150...150
Gives the deviation average value of the transmitted
signal in kHz
INPUT.MPX2.PEAK R
-150…150
Gives the deviation max peak value of the
transmitted signal in kHz
INPUT.MPX2.TYPE R/W
"MO" or "ST" or "ST+R+S" or
"ST+R" or "RDS" or
"RDS+SCA" or "SCA"
Sets the type of signal on the MPX1 input and
applies the corresponding filter
INPUT.MPX2.LEVEL R/W
-18.00...+18.00
Internal numerical gain
INPUT.MPX2.DRIVE R/W
-6.00...6.00
Drive setting, allows an increase of the input audio
level without changing the deviation setting.
