background image

1. Never permit children to play with or operate the garage door opener either from the wall station or the remote 

controls. Keep radio transmitter locked in the car. Misuse of the push button or transmitter could result in serious 
injury or even death. 

2. Open the garage door with the remote controls only when the garage door is fully visible to you and clear of all 

obstructions. The garage door should be kept in sight until it is completely open or closed and you are certain that the 
garage door opener has shut off. 

3. Attempting to exit the garage through the garage door opening, while the door is in motion, is a very dangerous 

activity that could result in serious injury or even death. 

4. Children and pets should always be clear of the door opening while the garage door is in motion. 

5. Check the safety reverse mechanism at least once a month to make sure that it will reverse with the minimum amount 

of force. Also check to be sure that the door will reverse within 5cm of the floor. See p.14. 

6. Check the manual operation of your garage door at least every 90 days to be sure that it is operating smoothly and 

does not bind or stick. Tighten all bolts on the door and visually check all hardware including springs for wear of 
damage. 

Caution

: If service is needed contact your local garage door service person. 

7. Do not decrease the safety reversing sensitivity mechanism to overcome a damaged or poorly operating door. This 

will adversely affect the operation of the safety reverse mechanism which could result in damage to the door, 
personal injury or even death. 

Caution:

Never operate the door opener if the reversing mechanism is not functioning properly. 

8. Whenever possible, the manual disconnect should only be used when the door is fully closed. Caution: Extreme care 

must be taken whenever the disconnect cord is pulled with the door partially open. Weak or broken springs may allow 
the door to fall rapidly resulting in property damage, personal injury or death. If a broken spring is evident, contact 
your local garage door service person immediately before disconnecting the door from the opener. Never attempt 
servicing a broken spring. 

9. Always disconnect electrical power supply to the opener when performing any maintenance or service to the opener 

or garage door. Failure to do so could result in electrical shock, property damage, personal injury or death. 

10. If any damage to any mechanical or structural component of the opener is observed, discontinue use and contact 

your local garage door service person immediately. 

11. If the door auto reverses, please ensure there is no obstruction to the track or door.  

After the Installation 

16

Summary of Contents for Guardian DCS2
























Reviews: