manualshive.com logo in svg

ECOCOACH ecoBatterySystem, Technical Manual

Share
Download
ECOCOACH ecoBatterySystem Technical Manual Download Page 25

4

 

Installation and commissioning

14. Press and hold the white push-button on the master until all LEDs flash in blue.

✓

All the ecoBatteryModules are switched off.

ATTENTION

Check that the ecoBatteryModules are actually switched off!

15. Connect all the ecoBatteryModules to the ecoBatterySystem power cables:

°

Black power cable to black connection

°

Red power cable to red connection

°

The power cables should click audibly into place and fit securely in the notch. Pull on the

connector firmly to check.

16. To be carried out by two people: Refit the control plate.
17. Reattach the cables and connectors to the control plate.

✓

The ecoBatteryModules are installed.

✓

For the next steps, see see chapter 4.4 "Installing the ecoBatterySystem".

INFORMATION

For more information on the ecoBatteryModule, please consult the documentation supplied by LG

Chem.

TM_ecoBatterySystem_2.2_en-UK

21

Summary of Contents for ecoBatterySystem















































Reviews:

No comments

Brands by name

Popular brands

Load more brands