manualshive.com logo in svg

ECOCOACH ecoBatterySystem, Technical Manual

Share
Download
ECOCOACH ecoBatterySystem Technical Manual Download Page 35

5

 

Expansions

12. Fit the cage nuts for the ecoBatteryModule (clearance: 8 slots (117 mm) down to the

tightened screw at the bottom).

13. To be carried out by two people: Slide the new ecoBatteryModule as far as it will go into the

slot.

INFORMATION

Make sure that cables do not get trapped.

14. To fit the power cables (red and black), parts of the cable conduit must be cut out with conduit

scissors.

15. Fit the red power cable to the positive front rail and the black power cable to the negative back

rail (just like the other cables).

INFORMATION

Tighten the power cable to a torque of 8 Nm.

16. Screw the ecoBatteryModule in place at the front.
17. Connect the battery’s terminal resistor to the new ecoBatteryModule (Slave X).
18. Connect the new ecoBatteryModule to the previous ecoBatteryModule (Slave 3) using the

battery connector cable.

TM_ecoBatterySystem_2.2_en-UK

31

Summary of Contents for ecoBatterySystem















































Reviews:

No comments

Brands by name

Popular brands

Load more brands