manualshive.com logo in svg

ECOCOACH ecoBatterySystem, Technical Manual

Share
Download
ECOCOACH ecoBatterySystem Technical Manual Download Page 33

5

 

Expansions

Procedure

DANGER

Voltage

An electric shock can lead to severe physical injury or death.

•

Switch off the ecoBatterySystem before carrying out any work on it.

°

Turn off the main fuse

°

Make sure power cannot reach the cables.

•

Only open the ecoBatterySystem when work is about to be performed on it.

1. Open the cabinet door.
2. Press the ON/OFF push-button(1).

Figure 6: The ecoBatterySystem control panel

✓

The green light in the ON/OFF push-button (1) goes off.

✓

The entire power supply is interrupted.

3. Undo the screws on the sides and remove the upper and lower cover plate.
4. In the ecoBatteryModule Master, press and hold the white push-button until all LEDs in the

ecoBatteryModule are off.

5. Unplug any cables and connectors attached to the control plate.

A

Fan (small fan, 1-way connector; large fan, 3-way connector)

B

ecoBatteryModule communication (Ethernet, 10-pin)

C

Inverter

D

DC power

TM_ecoBatterySystem_2.2_en-UK

29

Summary of Contents for ecoBatterySystem















































Reviews:

No comments

Brands by name

Popular brands

Load more brands