Eclipse ETEK 5 User Manual Download Page 4

Page: 4 / 80

CONTENTS

4 ETEK5 MANUAL

USING THE ETEK5

Details on how to get up and running quickly with your ETEK5.

This section is essential reading for everyone.

Factory set-up guide

Installing a 9v battery

Switching on the ETEK5

Switching off the ETEK5

Firing the ETEK5

Switching on the ETEK5 with OLED board fitted

Switching off the ETEK5 with OLED board fitted

Firing the ETEK5 with OLED board fitted

The ETEK5 circuit board

The ETEK5 OLED board

Using the Breech Sensor

Using the Breech Sensor with OLED board fitted

The ETEK5 navigation console

Setting up the ETEK5

Installing a barrel

Straight macroline fittings

Macroline hosing

Installing a preset air system

Attaching a loader

Setting the trigger

Adjusting the velocity

Adjusting the LPR pressure

Unloading the ETEK5

Storage and transportation

The tournament lock

Understanding the Breech Sensor operation

The battery level indicator

ADVANCED SET-UP

In depth information on setting up the ETEK5.

The

SET-UP

mode

Modifying a parameter

SET-UP

parameters

The PRESET parameter

Maximum ROF with Breech Sensor on (capped modes)

Maximum ROF with Breech Sensor off

DWELL -

Controls the amount of gas that is released with each shot

DEBOUNCE -

Adjusts the amount of trigger bounce

THE FACTORY RESET -

Resets all settings back to factory standard

ETEK5 OLED BOARD

In depth information covering all aspects of the ETEK5 OLED Circuit Board.

Installing the ETEK5 OLED board

ETEK5 OLED board navigation console

Switching on

Run screen layout

The Breech Sensor indicator

The lock indicator

The battery level indicator

The SETUP mode

PRESET - Selection of compliant preset firing modes

BS ON ROF - Maximum rate of fire with Breech Sensor on

BS OFF ROF - Maximum rate of fire with Breech Sensor off

KICK IN - Rate that the trigger must be pulled per second to begin ramping

RESTART - Time in seconds that ramping can restart after each trigger pull

DWELL - Solenoid energise time in milliseconds

DEBOUNCE - Trigger anti-bounce settings

SLEEP - Auto power off time in minutes

DISPLAY

- Defines what information is displayed on the run screen

ZERO

- Allows user to set the display variables to zero

Summary of Contents for ETEK 5

















































































Search results

Summary of Contents for ETEK 5

Reviews:

Related manuals for ETEK 5

Brands by name

Popular brands

Eclipse ETEK 5, User Manual

Search results

Summary of Contents for ETEK 5

Reviews:

Related manuals for ETEK 5

Brands by name

Popular brands