Eclipse ETEK 5 User Manual Download Page 9

Page: 9 / 80

USING THE ETEK5

ETEK5 MANUAL 9

SWITCHING ON THE ETEK5 WITH OLED BOARD FITTED

At the rear of the frame is the navigation console which houses the Select button

(labelled

figure 4A)

. This button is the disabling device for the ETEK5, used to switch

the marker on and off. Press and hold the button until the ETEK5 OLED board begins

its power up sequence.

1,2

SWITCHING OFF THE ETEK5 WITH OLED BOARD FITTED

Press and hold the button until the display shows GOODBYE. Release the button.

FIRING THE ETEK5 WITH OLED BOARD FITTED

If the Breech Sensor (BS) is disabled, pull the trigger to fire the ETEK5. If the Breech

Sensor is enabled and there is a paintball in the breech, pulling the trigger will also fire

the ETEK5. The entire firing sequence is controlled electronically by the ETEK5 board and

solenoid, enabling any user to achieve high rates of fire easily.

When the ETEK5 is turned on, the Breech Sensor is automatically enabled.

By continuing holding down the

button when turning on the ETEK5 OLED board the software

version number will be displayed.

FIG 4A

Summary of Contents for ETEK 5

















































































Search results

Summary of Contents for ETEK 5

Reviews:

Related manuals for ETEK 5

Brands by name

Popular brands

Eclipse ETEK 5, User Manual

Search results

Summary of Contents for ETEK 5

Reviews:

Related manuals for ETEK 5

Brands by name

Popular brands