EchoMaster Pro EMUBCAMKIT Installation Manual/User Manual Download

Page: 19 / 20

User Guide

tel - 1-800-477-2267

email - [email protected]

Illustrations are typical and may not match exact vehicle detail

Input Type

Sets input video type/resolution.

720p 25fps / 720p 30fps / CVBS PAL / CVBS NTSC

720p 30fps recommended

Output Type

Sets video output type/resolution.

720p 25fps / 720p 30fps / CVBS PAL / CVBS NTSC

This should match your monitor’s format.

Format

Formats the Micro SD Card.

This will erase any files on the

card!

Reset

Resets setting to factory defaults

Light freq

Sets lighting frequency to reduce flicker.

50Hz / 60Hz

Return

Select to exit the settings menu and
return to camera view.

Clock

Allows setting the time and date.
This is important for time-stamping
the recorded video files.

Version

Displays current firmware version.

EMUBCAMKIT

Universal Quad View Camera Kit

Summary of Contents for EMUBCAMKIT





















Search results

Summary of Contents for EMUBCAMKIT

Reviews:

Related manuals for EMUBCAMKIT

Brands by name

Popular brands

EchoMaster Pro EMUBCAMKIT, Installation Manual/User Manual

Search results

Summary of Contents for EMUBCAMKIT

Reviews:

Related manuals for EMUBCAMKIT

Brands by name

Popular brands