WARNING!
Maximum recommended vehicle speed for safe operation using the
Vacuum Mount model is 65 mph (104 km/h), when fitted to the center
of a vehicle roof of steel construction. Higher speeds could cause the
mount to fail, resulting in the minibar flying off of the vehicle, which
could cause damage to other vehicles, and injury or death to the pas-
sengers. The vacuum-magnet mount is not intended as a permanent
mounting for the minibar. The vacuum-magnet mount unit must be
mounted on a flat smooth magnetic surface (i.e. no fiberglass, ribbed
style roofs, etc.). Ensure that the magnet is kept clean.
Page 3 of 12
1.
Refer to the appropriate Vacuum Mount Installation for
the 5500 series, steps 2 through 9, and the corresponding
Figures for wiring instructions for the cord.
2.
Place hex nut into the hex shaped retaining cavity on the
inside of the minibar base.
3.
Place an internal star washer onto the enclosed M5 x 20
hex bolt and insert the hex bolt through the hole in the cup
magnet as shown. Hold the magnet/bolt assembly with the
bolt extended through the magnet as far as possible and
feed the hex nut and the shank of the bolt through one
of the openings at the 4 corners of the underside of the
minibar base. Maintain tension on the bolt/nut by holding
onto the cup magnet while tightening the assembly. Repeat
this process for all four corners. See Figure 5.
4.
Place the adhesive magnet covers over the magnets.
5.
Replace the lens.
Magnet Mount Installation for 5590 Series:
Figure 5
Note: The Magnet Mount is not recommended for use on
a moving vehicle, nor is it inteded as a permanent mount
for the light. Long duration usage of the magnet in the
presence of moisture will cause the steel to rust.
!
Operator is responsible for ensuring auxiliary plug
fits correctly into auxiliary power plug outlet used.
For proper operation, verify auxiliary power outlet
circuit is rated to supply a minimum of 10 amps.
(See specifications section for rated current in
amperes).
Do not exceed the current rating for the auxiliary
power outlet recommended by vehicle manufac
-
turer.
Keep auxiliary plug and outlet clean and free of
debris.
Do not use the auxiliary plug when wet.
Insert auxiliary plug fully into the outlet for proper
connection.
Grasp auxiliary plug, NOT cord, to remove from
outlet.
Remove auxiliary plug completely from outlet when
light is not in use.
WARNING!
Failure to follow these instructions can result in fire or injury
from excessive heat build up.
!
Flash Pattern Chart
SAE J845
CA T13
Sequence
Description
FPM
Phase
5590A
5590CA 5590CB 5590CC 5590CR
5597A
5597CA
5590A
5590CA 5590CB 5590CR
5597A
5597CA
1
Quad (Default)
75
A
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
1
Quad (Default)
75
B
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
2
Double
75
A
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
2
Double
75
B
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
3
Fast Double
130
A
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
3
Fast Double
130
B
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
4
Slow Quad
65
A
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS B CLASS B CLASS B CLASS B CLASS B
-
4
Slow Quad
65
B
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS B CLASS B CLASS B CLASS B CLASS B
-
5
Slow Double
65
A
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS B CLASS B CLASS B CLASS B CLASS B
-
5
Slow Double
65
B
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS B CLASS B CLASS B CLASS B CLASS B
-
6
Quint-hold
75
A
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
6
Quint-hold
75
B
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
7
Burst
75
A
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
7
Burst
75
B
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
8
Quad, Alternate Side-to Side
150
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
9
Quad, Diagonal Alternate
150
-
-
-
-
-
-
-
-
-
-
-
-
-
10
Double, Alternate Side-to-Side
150
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
11
Double, Diagonal Alternate
150
-
-
-
-
-
-
-
-
-
-
-
-
-
12
Quint-hold, Alternate Side-to-Side
150
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
13
Quint-hold, Diagonal Alternate
150
-
-
-
-
-
-
-
-
-
-
-
-
-
14
Fast Rotate
120
CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1 CLASS 1
-
-
-
-
-
-
15
Rotate/Quad
150/75
-
-
-
-
-
-
-
-
-
-
-
-
-
16
Wave Rotate
70
-
-
-
-
-
-
-
-
-
-
-
-
-
17
Random
-
-
-
-
-
-
-
-
-
-
-
-
-
18
Steady
-
-
-
-
-
-
-
-
-
-
-
-
-
