EAW KF755 Series Owner'S Manual Download Page 8

4.1.5

VA

4

DEFINED

The system overview illustrates that the KF700 Series development was driven by enhancing
the acoustical performance of the loudspeaker systems as it relates to its arrayability. Each
loudspeaker must therefore array effectively both horizontally and vertically. Consistent
controlled coverage patterns in three dimensions guarantees predictable array results
from venue to venue.

The development goals also dictated that the KF700 Series improve upon the time
domain behavior, particularly in the vocal region. The ability of a loudspeaker to maintain
the temporal integrity of the original input signal is easily as important as the frequency
response in determining the quality of the sound reproduction. Therefore, if harmonics
lead or lag fundamentals in the reproduction, then the original signal, and perhaps even
the intent of the performer, will be distorted. The ability to maintain the input signal’s
temporal integrity while delivering smooth frequency response to a well-defined coverage
area is ultimately the goal of any loudspeaker.

Consistently achieving the desired coverage from a loudspeaker array for a given venue 
is governed by performance in the three dimensions of space. Maintaining temporal
coherence is governed by the fourth dimension of time. Meeting all of these criteria truly
addresses system performance in four dimensions. This four-dimensional design
approach is VA

4

technology.

4.1.6

WEATHER-PROTECTED (WP MODELS)

The KF700P-WP and SB750P-WP models are weather-protected for permanent
installations. The exterior of the enclosure is laminated with a water-resistant fiberglass
coating. A 2-layer grille is used to prevent water from entering the front of the enclosure.
The outside layer is powder-coated perforated steel for physical protection. The rear layer
is a 1/8 inch thick foam to break up driven water droplets. Behind the grille assembly, a
layer of 100 x 100 wires per inch stainless steel mesh is affixed to the enclosure to prevent
any water spray from entering the front of the enclosure. The input panel and back
doghouse are weather-sealed with rubber strips to prevent water intrusion.

Section 5

Operation

5.1 KF700 

Series 

Products

5.1.1

KF700 MODELS

Model Name

Description

Primary Application

KF750F Three-way

Concert 

touring

KF750P

Three-way

Permanent installation

KF750P-WP

Three-way

Outdoor installation

KF755F 

Three-way

Concert touring downfill

KF755P

Three-way

Permanent installation downfill

KF755P-WP

Three-way

Outdoor installation downfill

SB750F

Dual 18-in.

Concert touring subwoofer

5.1.2

KF700 SERIES PRODUCT WEIGHTS

System 

Net (lb  /  kg)

Shipping (lb / kg)  

KF750F 

198  /  90.0 

230  /  104.6  

KF750P 

187  /  85.0 

201  /    91.4  

KF750P-WP 

205  /  93.2 

221  /  100.5  

KF755F 

198  /  90.0 

232  /  105.5  

KF755P

180  /  81.8 

203  /    92.3  

KF755P-WP 

205  /  93.2 

223  /  101.4  

SB750F 

193  /  87.7 

202  /     91.8  

KF750

KF755

2

Summary of Contents for KF755 Series

































Reviews: