background image

*Array size results in a Design Factor of less than the recommended 10:1. Refer to EAW Resolution for
further details.

Loom

6, 8, 10, 12, 14, 16 feet (6 tails) 

Extension:

 

12 feet 

CAUTION:

 There is no power switch on the loudspeaker. When connected to the AC mains, the 

loudspeaker will be fully operational, with the output level controlled by the signal source feeding the 
loudspeaker as well as by internal DSP. 

CAUTION:

 The supplied AC mains plug may not be appropriate for local AC mains receptacles. If not, 

have a qualified electrician remove the existing AC mains plug and install a plug appropriate for the AC 
mains supply receptacle and following all local codes. 

CAUTION:

 The chassis of this product is grounded through the grounding conductor of the power 

cord. To avoid electric shock, plug the power cord into a properly wired and grounded receptacle 
before making any connections to or operating the product. 

Electrical Warnings 

AC MAINS SUPPLY 

WARNING:

 Read all instruction and cautionary notes concerning electrical power in the EAW 

Loudspeaker Owner’s Manual. 

AC Mains Cable  

The AC mains cables supplied with the MotionLabs PDU mate with the Neutrik® powerCON™ TRUE1 AC 
MAINS jack on the loudspeaker. 

TRUE1 refers to both TRUE1™ and TRUE1 TOP™.  Phase in date depends on product. 

WARNING:

 Ensure that AC power supply has a properly grounded safety ground. Failure to follow this 

warning could cause equipment damage, injury, or death. 

Rigging

 

ADAPTive arrays are intended to be suspended or ground-stacked. This section details how to 
physically configure an ADAPTive Series column. The following are the recommended methods for 
most situations. Specific situations may require other methods. It is the user’s responsibility to 
determine the viability and safety for alternate methods and implement them accordingly. 

A Note about Splay Angles  

The Anya system requires no splay angles, with modules designed to be tight-packed in a straight 

vertical orientation. Vertical directivity is controlled exclusively via DSP. 

Summary of Contents for ADAPTive systems































Reviews: