Eaton
1121 Highway 74 South
Peachtree City, GA 30269
www.Eaton.com/lightingsystems
For service or technical assistance:
1-800-553-3879
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2018 Eaton
All Rights Reserved
Printed in USA
Publication No. IB503023EN
August 8, 2018
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
Procuct availability, specifications, and
compliances are subject to change
without notice.
Connecting to the building LAN or VLAN
Medium and large iLumin Plus panels may include the EG2
optional ethernet connection device. The EG2 acts as a host
for the iLumin series of remote applications including iOS
(iPhone/iPad
& Android OS devices). Coupling the EG2 to a Wi-Fi network
enables secure scene control, visual feedback and
modification from your hand held device. Once configured,
the EG2 automatically loads room and scene information
to the connected hand held device.
In addition to its handheld device capability, the EG2
houses internal webserver pages that allow for basic
scene control functions. These internal pages are
accessed through an internet browser and are password
protected for security.
The EG2 also facilitates the commissioning of the iLumin
Plus system, allowing our factory trained technicians
to use the EG2 connection to configure the iLumin Plus
system using iCANsoft on a LAN or Wi-Fi enabled PC or
via the internet rather than by connecting directly into the
iLumin Plus network.
• Factory default IP settings:
• IP Address: 192.168.0.100
• Mask: 255.255.255.0
• Gateway: 192.168.0.1
• DHCP: OFF
Note: The EG2 default settings are to use a
fixed IP address of 192.168.0.100. Any device
used to communicate with the EG2 will need to
be located within the 192.168.0.x subnet unless
IP address settings are changed.
Use the iCANsoft suite software package for
the configuration process.
Ethernet Connection
Wiring Information:
Connection: RJ45 connector
Use Category 5 or Category 6 cable minimum
Connect: Connect to building LAN or VLAN for lighting
network access.
*Note: The EG2 can be used to access the lighting network
via the buildign LAN or VLAN.
*Note: The EG2 can be use as a LAN bridge to connect
different building lighting networks as a single lighting network
over the building LAN or VLAN. See EG2 Bridge application
note for more information.
Sample iLumin Plus network systems
Below are some examples of a simple iLumin Plus network
and a complex iLumin Plus network application.
Simplified
Complete
wallstation
powerpack
0-10V LED
controller
occupancy/
daylight Sensor
2 wire controls wiring (polarity, topology free)
dual technology
occupancy sensor
iLumin Plus panel
ILS-0020
8 DALI buses
SCMD4
SCMD4
relay pack for
LED or plug load
LED luminaire with DALI driver
0-10V LED luminaire
S3
S2
S1
S0
B3
B2
B1
B0
A7
A6
A5
A4
A3
A2
A1
A0
+PWR -PWR
FRAME GND
RS 485 GNDRS 485- RS 485+
ETHERNET
FG
PWR-
PWR+
SG
A-
B+
Wallstation
Powerpack
iLumin
Touchscreen
iLumin
APP
SI-2
AV & Partitoning
Flacility Manager
ICANSoft Suite
Software
Building LAN or VLAN
RI-2
Relay Out
Occupancy/
Daylight Sensor
0-10V LED
controller
Wallstation
Occupancy/
Daylight Sensor
Wallstation
Building WLAN
ILL-3301
Large Panel
36 Relays, 36 0-10V, EG2 inside
TC1
Network timeclock
Circuit Breaker Panel
ILS-0020
Small Panel
0 Relays, 0-10V, 8 DALI bus
8 DALI buses
iCANet (Daisy chain CANBUS network using Belden 1502 or 1502P cable)
2 wire control wiring (polarity, topology free)
2 wire control wiring (polarity, topology free)
DALI bus (polarity, topology free)
Occupancy Sensor
SCD96
DMX Out
DMX Fixture
DMX Fixture
Blind
Control
Curtain
Control
Circuit Breaker Panel
ILM-2110
Medium Panel
24 Relays, 12 0-10V, 4 DALI bus
Circuit Breaker Panel
LDCM
(0-10V to Reverse
Phase Module)
Relay pack for
LED or plug load
Dual Tech
occupancy
sensor
LED Luminaire
with 0-10V driver
LED Luminaire
with DALI driver
24 Relays
and 12
0-10V zones
36 Relays
and
0-10V zones
Reverse phase track lighting
BMS Pro
BACnet
Building
Management
System
Warranties and Limitation of Liability
Please refer to
www.eaton.com/LightingWarrantyTerms
for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site
www.eaton.com/
LightingWarrantyTerms
pour obtenir les conditions
générales.
Garantías y Limitación de Responsabilidad
Visite
www.eaton.com/LightingWarrantyTerms
para
conocer nuestros términos y condiciones.
