Eaton G110 Series Installation Manual Download

Page: 40 / 45

Aligning Workstation to the Core

Connect the lift with connector base to the core via four (4) #1/4-20 screws (53956) and

#1/4-20 Kep nuts (18209 ).

Step



Genesys-Compatible Inside
Skin (Fabric, Laminate or
Steel)

90º Compound Corner
Shown

Connector Cover

Step



(4x)

Step



Connector Base
(G431A903)

Genesys Lift

(Shown for Reference Only)

5.  Install the grommet in the grommet opening in the core as shown below.

6.  Route cables from the lift through the grommet opening in the core as shown below.

7.  Install connector cover with four (4) screws (66714) as illustrated below.

Step



Step



(4x)

8. Install

compatible inside skins.

You have now completed the alignment of the workstation to the core.

www.eaton.com/powerquality 11-41 06-2011

Eaton Profile Genesys Dual-Lift Ergonomic Workstation Installation 36

Summary of Contents for G110 Series














































Search results

Summary of Contents for G110 Series

Reviews:

Related manuals for G110 Series

Brands by name

Popular brands

Eaton G110 Series, Installation Manual

Search results

Summary of Contents for G110 Series

Reviews:

Related manuals for G110 Series

Brands by name

Popular brands