Eaton FSO-2105 Service Manual Download

Page: 75 / 96

Front Section

Installation

WARNING!

Always replace the removed plug

with a new one to prevent leaks.

1. With a clean rag and solvent, clean the plug hole

and remove any remaining sealant compound.

Do not use sandpaper.

2. Apply sealant to the new plug and insert it into

the hole using the hands to guide the plug.

Note:

Apply

Eaton 677

to plugs.

EA048

EA049

2mm

3. Using the special tool E001020, hit with a

hammer to force the plug into the plug bore until

the plug penetrates 2 mm below the plug bore

top, that is the proper plug depth.

EA170

Removal

1. Inspect bushing and replace if worn.

Note:

Inspect other transmission bushing too.

The pictures here show only the front

housing bushing, however the procedure

is the same for all other transmission

permaglide bushing.

Note:

Use special tools E003001 and E030001.

Permaglide Bushing

247

2. Place a punch against the bushing outer diameter

through the lubrication hole.

EA055

3. Hit the punch and deform the bushing inward as

shown.

EA056

Summary of Contents for FSO-2105

































































































Search results

Summary of Contents for FSO-2105

Reviews:

Related manuals for FSO-2105

Brands by name

Popular brands

Eaton FSO-2105, Service Manual

Search results

Summary of Contents for FSO-2105

Reviews:

Related manuals for FSO-2105

Brands by name

Popular brands