background image

Powering Business Worldwide



© 2015 Eaton Industries (Canada) Co.

All Rights Reserved

Printed in Canada

Publication No. IM05805019K-002

April 2015

Eaton Industries (Canada) Co.

10725 - 25th Street NE, # 124 

Calgary, Alberta, Canada 

T3N 0A4 

Phone: +1-403-717-2000 

Fax: +1-403-717-0567 

email: [email protected] 

www.chfire.com

This information booklet is published solely for information 
purposes and should not be considered all-inclusive. If further 
information is required, you should consult EATON.

Sale of product shown in this literature is subject to terms and 
conditions outlined in appropriate EATON selling polices or 
other contractual agreement between the parties. This literature 
is not intended to and does not enlarge or add to any such 
contract. The sole source governing the rights and remedies of 
any purchaser of this equipment is the contract between the 
purchaser and EATON.

NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING 
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR 
MERCHANTABILITY, OR WARRANTIES ARISING FROM 
COURSE OF DEALING OR USAGE OF TRADE, ARE MADE 
REGARDING THE INFORMATION, RECOMMENDATIONS AND 
DESCRIPTIONS CONTAINED HEREIN. In no event will EATON be 
responsible to the purchaser or user in contract, in tort 
(including negligence), strict liability or otherwise for any 
special, indirect, incidental or consequential damage or loss 
whatsoever, including but not limited to damage or loss of use 
of equipment, plant or power system, cost of capital, loss of 
power, additional expenses in the use of existing power 
facilities, or claims against the purchaser or user by its 
information, recommendations and description contained 
herein.

Summary of Contents for FD120













































Reviews: