background image

11

Instruction Booklet  

IB0162063EN

Effective January 2014

O & M Manual for the EGS Metered, Service
Entrance Automatic Transfer Switch with Relay Control

Eaton Corporation www.eatoncanada.ca

5.4 Manual Operation

Warning

DO nOT aTTEMPT TO ManUaLLY OPEraTE THE aTS WiTH THE UTiLiTY 

Or gEnEraTOr aVaiLaBLE.

Warning

HigH VOLTagES arE PrESEnT in anD arOUnD TranSFEr SWiTCH 

EQUiPMEnT. BEFOrE aTTEMPTing TO ManUaLLY TranSFEr, 

DiSCOnnECT THE LinE POWEr FrOM THE EQUiPMEnT BEing SErViCED 

BY OPEning anD LOCKing OUT, iF POSSiBLE, THE nEXT HigHEST 

DiSCOnnECT DEViCE. FaiLUrE TO FOLLOW THiS PrOCEDUrE COULD 

CaUSE SEVErE PErSOnaL inJUrY anD/Or DEaTH. 

 

aLWaYS TUrn THE UTiLiTY POWEr OFF anD TUrn THE gEnEraTOr (iF 

a gEnEraTOr) COnTrOL SELECTOr SWiTCH TO THE “OFF” POSiTiOn 

BEFOrE aTTEMPTing a ManUaL TranSFEr.

Warning

inSUrE THE DEaDFrOnT iS inSTaLLED PriOr TO EnErgiZing THE 

TranSFEr SWiTCH.

To Manually Operate

Step 1:  Disconnect all sources of power.
Step 2:  Locate the manual lever between the solenoids..
Step 3:  Locate the handle used to manually transfer the switch.
Step 4:  Attach the handle to the manual lever.
Step 5:  Move the lever up to go to utility or move the lever down to go to 

generator.

Step 6:  Reconnect the power.

Figure 13. ATS Manual Operating Lever.

Figure 14. ATS Manual Operating Handle.

Summary of Contents for EGS Series



















Reviews: