Eaton Cutler-Hammer ATC-300 Instruction Booklet Download Page 28

Page: 28 / 32

ATC-300

Source 1

Source 2

Available

Connected

Load

Unit Status

Alarm
Reset

Engine

Test

Lamp

Test

Help

Step

Enter

Bypass

TDNE / TDEN

For more information visit: www.eaton.com

IB140024EN

Instruction Booklet

Page

Effective: October 2014

ATC-300/900 40-400A (480/600Vac)

3-Postion Contactor Based Transfer Switch

Figure 20. ATC-300+ Logic (Utility Supplying Load).
Step 6:

To view the setpoints, press the

<Step/Enter>

pushbut-

ton and enter the Password.

Note:

The factory default Password is 0300. Once all installation and

testing is complete, the Password should be changed by authorized

personnel to a unique Password for the equipment.

After entering the password, press the

<Step/Enter>

pushbutton until the VIEW SETPOINTS menu appears.

Select YES. Press the

<Step/Enter>

pushbutton to

scroll through the setpoints.

Summary of Contents for Cutler-Hammer ATC-300

































Search results

Summary of Contents for Cutler-Hammer ATC-300

Reviews:

Related manuals for Cutler-Hammer ATC-300

Brands by name

Popular brands

Eaton Cutler-Hammer ATC-300, Instruction Booklet

Search results

Summary of Contents for Cutler-Hammer ATC-300

Reviews:

Related manuals for Cutler-Hammer ATC-300

Brands by name

Popular brands