background image

 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

IF 1849

Champ LED Floodlight

NPFMA20L/25L LED Fixtures

Installation & Maintenance Information

IF 1849 • 03/19                                                          Copyright

®

 2019, Eaton’s Crouse-Hinds Division 

                                                    Page 1

WARNING

To avoid the risk of fire, explosion or electric shock,

 this product should be 

installed, inspected and maintained by a qualified electrician only, in accordance 

with all applicable electrical codes.

WARNING

To avoid electric shock:

• 

Be certain electrical power is OFF before and during installation and 

maintenance.

• 

Floodlight must be supplied by a wiring system suitable per local code with 

an equipment grounding conductor.

To avoid burning hands:

• 

Make sure LEDs and drivers are cool to touch when performing 

maintenance.  

WARNING

To avoid potentially unsafe operating conditions:

• 

Make sure the supply voltage is the same as the rated floodlight voltage.

• 

Do not operate in ambient temperatures above those indicated on the 

floodlight nameplate.

• 

Use only replacement parts from Eaton’s Crouse-Hinds Division.

• 

Use proper supply wiring as specified on the floodlight nameplate.

• 

All surfaces must be clean.

• 

LED compartment non-serviceable.  Do not open.

• 

Before opening wiring compartment, electrical power to the floodlight 

must be turned off.  Keep tightly closed when in operation. 

INSTALLATION

Mounting
 

Yoke Mount - Wall Mount Using Floodlight Yoke Only

1. 

Using floodlight yoke as a template, mark and drill desired location on mounting 

surface.

2. 

Secure floodlight yoke to surface using ½” bolts or lag screws (not provided).

WIRING

 

Wiring the Floodlight

1. 

Open back cover/heat sink by loosening nine (9) #10-24 x 0.75” stainless steel 

cover screws using a 5/16” nut socket or flat head screwdriver (see Figure 1).  

The heat sink cover should be removed by pulling back on one corner of the top 

most edge to prevent damage to gasket.

NOTE: 

To avoid pinching hazard between heat sink cover and driver housing, ensure 

that floodlight is oriented in vertical position before, and during, wiring procedure.

2. 

All components in the fixture are pre-wired so only line in, neutral and ground 

need to be connected in the fixture using the supplied Wago connectors, using 

methods that comply with all applicable codes.  See Figure 2 for wiring diagram.

• 

Wire range from AWG 18-14 (0.75 - 2.5mm²) for neutral, and line (strip 

length 0.43” [10.9mm]), and AWG 16-14 (1.5 - 2.5mm²) for ground 

connections (strip length 0.43” [10.9mm]).

• 

Entries to driver housing shall be sealed, using HTL or STL, with 

devices rated a minimum of IP66.

• 

Standard openings are M20, M25 or 3/4” NPT.

• 

Optional openings are M20 (20mm) and/or M25 (25mm).

• 

Secure all electrical connections and wiring entry glands.

• 

Ensure that the following lengths for field wiring, internal to the driver 

housing compartment, are followed:

      – 4.5” ± 0.25” (114 ± 6mm) for ground wire

       – 2.5” ± 0.25” (64 ± 6mm) for neutral wire

       – 2” ± 0.25” (51 ± 6mm) for line in wire

APPLICATION

Pro Flood LED floodlights’ construction is designed for use indoors and outdoors in 

marine and wet locations, where moisture, dirt, corrosion, vibration and rough usage 

may be present.

• IEC 60598-1 and IEC 60598-2-1

• Wet Locations

• IP66

• CE marked

Champ

 

LED floodlights’ construction is designed for use indoors and outdoors in 

marine and wet locations, where moisture, dirt, corrosion, vibration and rough usage 

may be present.

Champ

 

LED floodlights are supplied for use with a choice of voltages

:

• 100-277 VAC, 50/60 Hz

• 127-300 VDC

• 347-440 VAC, 50/60 Hz

COVER SCREWS

LINE TERMINAL 

NEUTRAL TERMINAL 

GROUND TERMINAL 

Figure 1

Cover/heat sink

DO NOT PLACE 
ADDITIONAL WEIGHT 
ON THE BACK COVER/
HEAT SINK

Summary of Contents for CROUSE-HINDS Champ NPFMA20L













Reviews: