EASTMAN Kodak X-Omat 180 LP, Service Manual

Page: 5 / 134

Installation
1C7833 – July 1995 1–1
Section 1: Installation
Description Page
Table of Contents
Special Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Checking the Packing List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Before Starting the Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Removing the TOP COVER and the HINGE PLATES
from the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Installing the New HINGE PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Installing the SORTER on the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
Installing the ENCODER WHEEL/SPROCKET and Adjusting the Height of the
DRIVE SHAFT on the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
Installing the New COVER on the ELECTRICAL BOX . . . . . . . . . . . . . . . . . . . . . . 1-17
Installing the New ELECTRICAL BOX HARNESS . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
Placing the New ELECTRICAL BOX HARNESS in Position . . . . . . . . . . . . . 1-19
Connecting the New ELECTRICAL BOX HARNESS to J10 and TB5 . . . . . . 1-20
Connecting the New ELECTRICAL BOX HARNESS to the 500 BOARD . . . 1-22
Modifications to the 500 BOARD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27
Installing the SORTER HARNESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28
Installing the COVER EXTENSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-31
Installing the New SPRINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32
Installing the FILM TRAY and the TOP COVER of the SORTER . . . . . . . . . . . . . . 1-34
Adjusting the Temperature of the DRYER in the PROCESSOR . . . . . . . . . . . . . . . . 1-34
Final Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-35
Checking the SWITCHES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-35
Checking the BIN SENSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-37
Checking the DIVERTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-38
Installing the PANELS and Checking for Correct Operation of the SORTER . 1-38
Special Tools Required
--
PORTABLE COMPUTER, IBM compatible with MS-DOS version 3.0 or
higher on the hard drive, 720 KB 3
1
⁄
2
in. disk drive, and a serial port
configured as COM1.
5B6278
DIAGNOSTICS DISKETTE
TL-4390 SCALE
TL-4391 INTERFACE CABLE
TL-4430 PROM EXTRACTION TOOL
TL-4598 PIN EXTRACTION TOOL