background image

11

Easee public knowledge base can be found at 

easee.support

.

Charging Robot interface

Light description

Status

White – constant light, only at the bottom 
2 LEDs – master unit / 1 LED – secondary units

Standby

White – constant light

Car connected

White – pulsating light

Charging in progress

Blue – constant light

Smart charging enabled (car connected)

Blue – pulsating light

Smart charging in progress

At startup, the LEDs turn on one by one. 
When the charger is updating, one or more 

LEDs will flash green while this is in progress.

Updating software (updating can take up to 30 minutes)

NOTICE!

 The car must be disconnected before a software update 

can be completed.

White – flashing light

Waiting for authentication by an RFID tag. Hold the RFID 

tag against the RFID area of the Charging Robot in order to 

authenticate and initiate the charging.

White – fast flashing light

RFID-tag received (awaiting key verification)

Red – constant light

General error. Unplug the charging cable and replug it to the 

Charging Robot. If the red light persists, check the Easee app or our 

knowledge base

1

 for further information.

Red – constant light, with warning sounds

Wires are connected incorrectly. Consult an authorised electrician.

Red – pulsating light

The Charging Robot has measured an abnormal temperature and 

has entered in safe mode. Please go to our knowledge base

1

 for 

further information.

White – flashing light, only at the bottom

The Charging Robot is searching for its master unit. Please check 

the status of the master unit. For further information, please check 

our knowledge base

1

.

Yellow – flashing light, only at the bottom

The Charging Robot is waiting to be configured. Consult an 

authorised electrician.

Summary of Contents for Plug and Play

















Reviews: