background image

13

Max transmitted power

Radio:

 100 mW at 863–870 MHz. 

WiFi:

 50 mW at 

2.4–2.472 GHz. 

GSM:

 2 W at 880–915 MHz, 1 W at 

1710–1785 MHz, 200 mW at 703–748 MHz, 832–862 MHz, 

880–915 MHz, 1710–1785 MHz and 1920–1980 MHz.

Product life cycle

Transportation: 

The charger should always be 

transported within its original packaging. No other 

items should be stored on top of the box other than 

Easee chargers. Should the box be dropped or otherwise 

impacted, a visual inspection should be done in order to 

verify potential damage.

Storage: 

The electronics are hermetically sealed and 

will not get damaged if stored in humid areas. However, 

in order to preserve the packaging and its contents, 

we recommend storage in a tempered, dry and well-

ventilated area. Relative humidity should not exceed 

80% and no corrosive gas should be present. Storage 

or transportation environment should never exceed the 

limits provided in the technical specifications of the 

charger (see page 5).

Dismounting:

 Perform a factory reset of the device 

before powering it down. This is done via the Installer 

app. Dismounting shall only be performed by an 

authorised electrician. The power supply to the charger 

must be isolated before dismounting starts. Use the 

installation guide and follow the steps in reverse in order 

to dismount the Charging Robot in the correct order.

Disposal: 

This electronic equipment must not be 

disposed of in household waste. For the return of old 

devices, free collection and acceptance points may be 

available in your vicinity. Observe local regulations for 

correct and environmentally friendly disposal. If the old 

electronic equipment contains personal data, you are 

responsible for deleting it yourself before returning it.

Padlock dimensions

Max total lock height: 56 mm. Shackle height (outer 

dimension): 19–20 mm. Shackle thickness: 3.2–4 mm. 

Data protection

When the product connects to the Internet, personal 

data is sent to Easee AS. You will receive more 

information about data protection during the 

configuration of your Charging Robot.

Repair

If your charger needs to be repaired, please contact your 

Easee supplier.

Returns and complaints

Contact your distributor or Easee Customer Support 

regarding the return and complaint of your product.

Customer support

Download the latest manuals, find answers to frequently 

asked questions and useful documents and videos for 

your product at 

easee.support

.

Contact details

Easee AS

Grenseveien 19

4313 Sandnes, Norway

Org. nr: 920 292 046

You can find additional contact details for your country 

a

easee.com

.

Summary of Contents for Plug and Play

















Reviews: