background image

9

 

 

 

LCD 

 

ONYX Sports Class Commuter  comes  with the 

multifunctional LCD power assist  display.  The display is 

mounted on the left side of the handlebar and has three 

main buttons

 (Power, -, +)

, and a monitor. 

 

ON/OFF 

 

By pressing the Power button for a couple of seconds, the display turns on and activates the power supply. To turn the 

display off and deactivate power supply to the bike, long press the Power button again. When the bike is not in operation, 

and no buttons are pressed for 10 minutes, the display will automatically turn off. When the e-bike system is switched off, 

the leakage current is less than 1 μA.

 

 

DISPLAY CONTENT 

 

 

Pedal Assist System (PAS) – Level selection 

ONYX comes with 5 levels of pedal assistance. To change the PAS level, click 

(+)

 

or

 (-)

 buttons to increase or decrease the levels. To avoid accidental use of the 

PAS or throttle, make sure to keep the LCD turned off at all times when the bike is 

not in use. 

 

 

 

Walk Power Assist 

Riders can use up to 6 km/h power assist function when pushing the bike. Hold 

(-)

 

button to activate the Walk Power Assist function. 

P

 letter will appear on the screen 

and the bike will start moving at the speed of no more than 6 km/h. Release 

(-) 

button to exit Walk Power Assist function. 

 

 

 

Speed 

After the e-bike system is switched on, the display shows current speed by default. To change the indicating information, 

press 

Power 

to  show  in  turn:  Current  Speed  (Km/h)  →  Trip  Distance  (Km)  →ODO  (Km)  →

 

Trip  Time  (Hour)  → 

Average Speed (Km/h) → Max Speed (Km/h). Each state will display for 2 seconds and then

 automatically return to 

current speed interface. If the display is set to miles, the data will be presented respectively. 

 

 

 

Summary of Contents for ONYX




















Reviews: