background image

10

 

 

 

Battery Capacity Indicator 

When the battery is fully charged, the icon shows five full bars on the top left corner 

of the display. When the battery is low on change, the indicator starts flashing. 

 

 

 

Power 

The output power of the motor is indicated in the middle of the interface. 

 

 

Error Code Definition 

When the electric control system of the bike is out of order, the display automatically 

displays  the error code and stops  working  correctly. The reason for the error is 

shown in the error code definition table below.

 

 

 

Error Code

 

Definition

 

21 

Current Abnormality 

22 

Throttle Abnormality 

23 

Motor Phase Abnormality 

24 

Motor Hall Signal Abnormality 

25 

Brake Abnormality 

30 

Communication Abnormality 

 

FAQ 

Why does the display not turn on?  

Check the connections between the display and the controller. Make sure the battery is charged.

 

The display shows an error. What to do?

 The error code will disappear once the issue associated with it is resolved. Check 

bicycle components and wires for any signs of damage. Disconnect and re-connect the main wire harness at the handlebar, 

recharge battery, and check LCD again. Contact your dealer or e-JOE for further instructions. 

 

For more information about the display and its advanced settings, refer to the official LCD manual. 

 

THROTTLE 

 

ONYX Sports Class Commuter is equipped with a throttle that allows you to speed up to 25 mph 

without pedaling at all. The thumb throttle is mounted on the left side of the handlebar. 

 

The throttle is activated once the LCD Display is turned on. To use the throttle and apply power to 

the motor, slowly press its lever down with a thumb. The throttle provides smooth acceleration when 

pressed slowly and gradually. 

 

The throttle mechanism allows to activate pull power from a stop, and inexperienced users should take extra care when first 

applying the throttle. We recommend beginning the ride with pedaling first and then applying the throttle. Always be aware 

of your surroundings. Do not use the throttle unless you are ready to ride. As a precaution, turn the LCD off after riding to 

avoid accidental activating of the throttle or PAS.  

 

Summary of Contents for ONYX




















Reviews: