E.F. Johnson Company CONVENTIONAL VOTING RECEIVER User Manual Download Page 74 | Manualshive

Page: 74 / 148

background image

800 MHz RECEIVER

4-6

July 2000
Part No. 001-2000-720

Full CVR

This menu selection walks through the align-

ment of the entire repeater. The Receiver and Exciter
portions are performance tests and adjustments. The
Audio and Data portions are level adjustments for the
CVR Interface Board. Refer to Figure 4-29 for an
alignment points diagram for the Interface Board.

CVR To Voter Interface

Figure 4-22 CVR TO VOTER INTERFACE

This menu selection walks through the align-

ment of the audio output level setting of the receiver.

4.2.7 UTILITIES

Figure 4-23 UTILITIES MENU

COM Port

This is the COM port used to send and receive

data from the Repeater MPC. An interface cable con-
nects the Repeater to the computer (see Figure 4-25

).

Figure 4-24 COM PORT SELECTION

Figure 4-21 TEST PROGRAMMING FLOWCHART

All Test

Receiver Test

TCXO Frequency Adjust

Audio Distortion

Hum & Noise Measurement

SINAD Measurement

Squelch Adjust

Data Level Adjust

Miscellaneous Tests

Receiver

TEST

All Receive Tests

All Operational Tests

Handshake Test

Alarm Test

Full Rptr/Station/CVR

Voter Interface

CVR Setup

RSSI Adjustment (Factory)

RSSI Adjustment (Field)

CVR Operation

CVR Audio Level Adjustment

CVR FSK Level Adjustment

Revert Audio Adjustment (Local Site Only)

«
...
72
73
74
75
76
...
»

Summary of Contents for CONVENTIONAL VOTING RECEIVER





















































































































































Reviews:

No comments

Related manuals for CONVENTIONAL VOTING RECEIVER

Brand: Baofeng Pages: 4

Brand: Baofeng Pages: 22

Brand: JFSound Pages: 52

Brand: RadioLink Pages: 4

Brand: Radio Industries Pages: 26

Brand: Vanderbilt Pages: 5

Brand: Lectrosonics Pages: 16

Brand: Barlow Wadley Pages: 11

Brand: Cirronet Pages: 64

Brand: nedis Pages: 84

Brand: Integra Pages: 112

Brand: CommRadio Pages: 27

Brand: Dahua Pages: 12

Brand: Dual Pages: 20

Radio-To-Intercom Bridge RIB-600Analog

Brand: Ritron Pages: 36

Brand: GAMA Electronics Pages: 4

Brand: Icom Pages: 48

Brand: Onkyo Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands