E.F. Johnson Company CONVENTIONAL VOTING RECEIVER User Manual Download Page 3 | Manualshive

Page: 3 / 148

background image

-3

February 1996

Part No. 001-3039-505

C

ONVENTIONAL

V

OTING

R

ECEIVER

Copyright



2000 by the E.F. Johnson Company

The E.F. Johnson Company designs and manufactures two-way radio equipment to serve a wide variety of communications
needs. Johnson produces equipment for the mobile telephone and land mobile radio services which include business, indus-
trial, government, public safety, and personal users.

LAND MOBILE PRODUCT WARRANTY

The manufacturer’s warranty statement for this product is available from your product supplier or from the E.F. Johnson Com-
pany, 299 Johnson Avenue, Box 1249, Waseca, MN 56093-0514. Phone (507) 835-6222.

WARNING

This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harm-
ful interference. In addition, changes or modification to this equipment not expressly approved by E. F. Johnson could void
the user’s authority to operate this equipment (FCC rules, 47CFR Part 15.19).

DO NOT allow the antenna to come close to or touch, the eyes, face, or any exposed body parts while the radio is transmitting.

DO NOT operate the radio near electrical blasting caps or in an explosive atmosphere.

DO NOT operate the radio unless all the radio frequency connectors are secure and any open connectors are properly
terminated.

DO NOT allow children to operate transmitter equipped radio equipment.

SAFETY INFORMATION

Proper operation of this radio will result in user exposure below the Occupational Safety and Health Act and Federal Commu-
nication Commission limits.

The information in this document is subject to change without notice.

E.F. Johnson Company will not be liable for any misunderstanding due to misinformation or errors found in this
document.

LTR, LTR-Net, Multi-Net, Viking Head/EFJohnson Logo, Call Guard and SUMMIT are registered trademarks of E.F. Johnson
Company All other company and/or product names used in this manual are trademarks and/or registered trademarks of their
respective manufacturer.

«
1
2
3
4
5
...
»

Summary of Contents for CONVENTIONAL VOTING RECEIVER





















































































































































Reviews:

No comments

Related manuals for CONVENTIONAL VOTING RECEIVER

Brand: iDirect Pages: 82

Brand: Cables to Go Pages: 5

Brand: MAC Audio Pages: 12

Brand: Akai Pages: 33

Brand: Renault Pages: 384

Brand: Icom Pages: 7

Brand: Sansui Pages: 50

Brand: Zenith Pages: 70

Brand: GE Pages: 24

Brand: Teac Pages: 200

Brand: Kramer Pages: 41

Brand: Strong Pages: 22

Brand: Sena Pages: 27

Brand: Aiwa Pages: 14

FatMax FMHT1-77360

Brand: Stanley Pages: 154

Brand: Boss Audio Systems Pages: 41

Brand: ZyXEL Communications Pages: 1

Brand: Toughbook Arbitrator Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands