E.F. Johnson Company CONVENTIONAL VOTING RECEIVER User Manual Download Page 49

Page: 49 / 148

UHF RECEIVER

3-7

July 2000

Part No. 001-2000-720

Figure 3-25 LAPTOP INTERCONNECT CA-

BLE

Display Mode

This screen allows the color mode to be selected

for color monitors. When using a laptop, monochrome
is recommend for better resolution.

Figure 3-26 COLOR MODE SELECTION

Alarm Display

This screen displays a scrolling list of alarms gen-

erated by the repeater.

User Level

There are two levels to choose from, Novice and

Advanced. The Novice uses prompts in the Edit-
Parameters screens when Escape or F2 keys are
pressed that ask "are you sure" before the task is exe-
cuted. The Advanced selection performs the task with-
out asking the question.

Figure 3-27 USER LEVEL

3.2.8 CVR PROGRAMMING

Creating A New File

An example will be used to show the program-

ming for a new file created for Site 1.

NOTE: At any point in the programming sequence, if
F1 is selected, a help screen appears to explain the
menu selection highlighted at that point.

Select CVR To Edit

A CVR is selected to program. When no file

exists with programmed CVRs, the default is selected
and edited.

1. Highlight EDIT, press Enter.

2. Highlight SELECT REPEATER, press Enter.

3. Default is the only repeater in this list, press Enter.

4. Highlight EDIT, press Enter.

5. Highlight SETUP PARAMETERS, press Enter.

6. The Setup Parameters screen appears (see

Figure 3-7). Fill in the parameters for this repeater.
A brief description of the parameters is in Table
3-1. Full descriptions are in Section 3.2.3.

TO LAPTOP

TO CVR

Summary of Contents for CONVENTIONAL VOTING RECEIVER





















































































































































Search results

Summary of Contents for CONVENTIONAL VOTING RECEIVER

Reviews:

Related manuals for CONVENTIONAL VOTING RECEIVER

Brands by name

Popular brands

E.F. Johnson Company CONVENTIONAL VOTING RECEIVER, User Manual

Search results

Summary of Contents for CONVENTIONAL VOTING RECEIVER

Reviews:

Related manuals for CONVENTIONAL VOTING RECEIVER

Brands by name

Popular brands