E.F. Johnson Company 5300 ES Series Operating Manual Download Page 115 | Manualshive

Page: 115 / 142

background image

5300 ES Series Mobile Radio Operating Manual

9-3

Password Description

9.2.3

Master Password

The Master Password overrides all the preceding passwords. It can be used by a system
administrator as a “pass key” to a password controlled function or to change a lost or
inadvertently changed password. Master passwords are set up and changed the same as the
other passwords. It does not override the following Zone Password.

9.3

Zone Password

A zone password can be programmed with the 5300 ES mobile radio. It prevents
unauthorized reprogramming of zones by keypad programming.

Note

The programming and usage of this password has not changed. It is independent from the
preceding passwords, and programmed using PC Configure.

«
...
113
114
115
116
117
...
»

Summary of Contents for 5300 ES Series















































































































































Reviews:

No comments

Related manuals for 5300 ES Series

Brand: MAJORITY Pages: 20

VXD-720 digital

Brand: Vertex Standard Pages: 28

Brand: Acconeer Pages: 36

Brand: Major tech Pages: 17

Brand: GPX Pages: 2

Brand: Tait Pages: 74

Brand: Logik Pages: 24

Brand: Gogen Pages: 28

Brand: Craig Pages: 4

Brand: Citizen Pages: 5

Brand: Vertex Standard Pages: 2

Brand: Midland Pages: 40

Brand: AEG Pages: 22

Brand: AEG Pages: 62

Brand: AEG Pages: 86

Brand: AEG Pages: 82

Brand: AEG Pages: 38

Brand: AEG Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands