E.F. Johnson Company 5300 ES Series Operating Manual Download Page 113

Page: 113 / 142

March 2008

5300 ES Series Mobile Radio Operating Manual

9-1

E C T I O N

Section9

Password Description

A password feature is available for 5300 ES mobile radios. The following passwords may
be set:

• Four Power-On (User x) Passwords

• Download and Upload Passwords

• Master Password

Software Versions Required:

PC Configure 2.4.1 or later is compatible with 5300 ES Mobile radios Version 6.x.x or
later Models

9.1

Programming Passwords

Passwords are programmed using PC Configure. The applicable radio must be connected
to the computer and powered up to display this screen.

Note

Any password changes made to the radio will be immediately applicable when Password
Management is exited.

Password data is transferred and stored in an encrypted format for security purposes. In
addition, actual passwords are never displayed. They are always indicated by eight
asterisks (********).

Summary of Contents for 5300 ES Series















































































































































Search results

Summary of Contents for 5300 ES Series

Reviews:

Related manuals for 5300 ES Series

Brands by name

Popular brands

E.F. Johnson Company 5300 ES Series, Operating Manual

Search results

Summary of Contents for 5300 ES Series

Reviews:

Related manuals for 5300 ES Series

Brands by name

Popular brands