E.F. Johnson Company 5300 ES Series Operating Manual Download Page 78 | Manualshive

Page: 78 / 142

background image

5-26

5300 ES Series Mobile Radio Operating Manual

Conventional Features

TG ID (P25 Only) - Selects the talk group for the selected channel. Rotate the Select
switch to display the alias of each preprogrammed talk group and then press it to store
the desired talk group.

Transmit Type (P25 Mixed Mode Only) - If the selected channel is a mixed mode,
analog and P25 channel, this selects the transmit type. Either Analog or Digital (P25)
can be selected. This then determines if a Tx Code or Tx NAC is programmed above.

«
...
76
77
78
79
80
...
»

Summary of Contents for 5300 ES Series















































































































































Reviews:

No comments

Related manuals for 5300 ES Series

Brand: Icom Pages: 15

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 21

Brand: ICP DAS USA Pages: 6

BELT-PAK 5 Series

Brand: EARMARK Pages: 2

Brand: Vitek Pages: 6

Brand: EKO Pages: 12

Brand: Kompernass Pages: 3

Brand: Hamilton Beach Pages: 10

DAY BREAK RA 5015

Brand: Karma Pages: 12

Brand: Yaesu Pages: 2

Brand: Radio Shack Pages: 12

Brand: Radio Shack Pages: 2

Brand: PURE Pages: 88

Brand: Gogen Pages: 28

Brand: Garmin Pages: 174

Brand: JVC Pages: 32

KT-SR2000 - Sirius Satellite Radio Tuner

Brand: JVC Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands