background image

5

User Manual EE872 Modular Probe for CO

2

, RH, T and p

1.2.1  Mounting and Start-up

The device has been produced under state of the art manufacturing conditions, has been thoroughly 

tested and has left the factory fulfilling all safety criteria. The manufacturer has taken all precautions to 

ensure safe operation of the device. The user must ensure that the device is set up and installed in a 

manner that does not have a negative effect on its safe use.

The user is responsible for observing all applicable safety guidelines, local and international, with 

respect to safe installation and operation on the device. This user manual contains information and 

warnings that must be observed by the user in order to ensure safe operation.

•  Mounting, start-up, operation and maintenance of the device may be performed by qualified staff only. 

Such staff must be authorized by the plant operator to carry out the mentioned activities.

•  The qualified staff must have read and understood this user manual and must follow the instructions 

contained within.

•  All process and electrical connections shall be thoroughly checked by authorized staff before putting 

the system into operation.

•  Do not install or start-up a device supposed to be faulty. Make sure that such devices are not 

accidentally used by marking them clearly as faulty.

•  A faulty device may only be investigated and possibly repaired by qualified, trained and authorized 

staff. If the fault cannot be fixed, the device shall be removed from the system.

•  Service operations other than described in this user manual may only be performed 

by the manufacturer.

2  Scope of Supply

•  EE872 according ordering guide

•  Test report according to DIN EN10204-2.2

•  Quick User Guide

2.1  Accessories

•  E+E Product Configuration Software  

(Free download from 

www.epluse.com/Configurator

) EE-PCS

•  Modbus configuration adapter  

HA011018

•  Connection cable M12 - flying leads 

1.5 m (59.06”) / 5 m (196.85”) / 10 m (393.70”) 

HA010819/20/21

•  T-coupler M12 - M12  

HA030204

•  M12 cable connector for self assembly  

HA010708

•  Protection cap / calibration adapter  

HA010785

•  Protection cap for the M12 cable socket  

HA010781

•  Protection cap for the M12 plug of EE872  

HA010782

•  Mounting flange  

HA010226

•  Wall mounting clip Ø 25 mm  

HA010227

•  Radiation shield  

HA010510

•  M12x1 flanged coupling with 50 mm (1.97”) stranded wire HA010705

2.2  Spare Parts

•  PTFE filter cap 

HA010123

•  Catalytic filter cap for H

2

O

2

 sterilization 

HA010124

•  Replacement sensing module 

EE872S-...

EE872S-

 

Model

CO

(default: heated)

M10

CO

2

 + p (default: heated)

M15

CO

2

 + T + RH + p (default: not heated)

M13

CO

2

 range

1)

0...

000 ppm

HV1

0...

000 ppm

HV2

0...1 % (10 000 ppm)

HV3

0...3 % (30 000 ppm)

HV5

0...5 % (50 000 ppm)

HV6

1) The CO

2

 range of the EE872S must be the same as of the original EE872 probe.

Summary of Contents for EE872 Series















Reviews: