manualshive.com logo in svg

Dynamic DYN-6336-02, Owner'S Manual, Page: 22 / 36

Share
Download
Dynamic DYN-6336-02 Owner'S Manual Download Page 22

 

22 

8. 

Color Lighting 

can be operated as follows:  First, you will need to install the battery. 

Once the battery has been inserted into the remote, you are ready to operate the 
color therapy lighting system . Press the READING LIGHT button on the sauna 
control panel. The white light will come on. While pointing the remote at the ceiling 
light, you can press any of the colors on the remote and that color will be displayed. 
You can use the SHADE button on the remote to go through a sequence of colors. 
If you want to turn the light off during your sauna session, you can press the 
POWER button on the remote. 

Please note:  You must be inside the sauna room 

for the remote to work.

 

 

 

 

 

 

 

9. 

Bluetooth 

can be used on the sauna room.  You first will need to pair your device 

with the sauna room.  Open your device’s Settings Menu and then locate and open 
Bluetooth.  You will find “

iSauna” 

or

  

“BT100” 

or

 

“Bluetooth”

.  Now you can pair 

your device.  Once pairing is successful, your device will be connected.  Please 
note that you must unpair/disconnect from Bluetooth if your sauna model has the 
optional MP3 Jack at the ceiling and you choose to use the Aux Wire to connect to 
the speaker system.  If you need to reset the Bluetooth/Aux system, you can do so 
by unplugging the sauna’s power cord for 15 minutes. 

10. 

The  MP3  Jack 

will  allow  you  to  connect  your  musical  device  using  the AUX  wire.  

Plug  one  end  of  the AUX  wire  into  your  musical  device  and  the  other  end  into  the 
MP3 Jack at the ceiling.  Do not leave the AUX wire connected at the ceiling when 
not using this function as it may cause static interference at the speakers.  You will 
control the volume and choose the music on your device.  When you disconnect the 
MP3 wire, the sound system will automatically return back to the Bluetooth mode.         

 

 

Please Note: On average, it takes our model saunas approximately: 
     *20 minutes to reach into 100 degrees Fahrenheit/38 degrees Celsius (with a  
     Starting temperature above 70 degrees Fahrenheit/21 degrees Celsius) 
     *25-30 mins to reach about 115-120 degrees Fahrenheit/46-49 degrees Celsius  
      (depending on sauna model) 
     *35-40 minutes to reach about 125-130 degrees Fahrenheit/52-54 degrees  

Summary of Contents for DYN-6336-02





































Reviews:

No comments