Dynalink RTA230 Page 67 User Manual Download | Manualshive

Page: 67 / 88

background image

Chapter 5:Connection Mode

59

PPP over Ethernet (PPPoE) Mode

RDAIUS
Server

AAA

BRAS

STM-1

DSLAM

Loop

Dynamic Public IP
assigned by BRAS

PPPoE+NAT+DHCP
on Private LAN

Hub

ADSL
Router

Ethernet

PC(S)

192.168.1.3

192.168.1.2

PPP over Ethernet

Default Private IP

192.168.1.1

*BRAS: Broadband
Remote Access Server

ISP

(Internet Service Provider)

Description:

In this deployment environment, the PPPoE session is between the ADSL WAN interface and BRAS.
The ADSL Router gets a public IP address from BRAS when connecting to DSLAM. The multiple
client PCs will get private IP address from the DHCP server enabled on private LAN. The enabled
NAT mechanism will translate the IP information for clients to access the Internet.

Configuration:

1.

Start up your browser and type

192.168.1.1

as the address to enter this ADSL web-based

manager.

2.

Go to

Quick Setup

. Type in the

VCI

and

VPI

value. Then click the

Next

button. eg:

VPI – 0
VCI – 39

3.

On the

Configure Internet Connection -Connection Type

page, select the

PPP over ATM

(PPPoA)

then click the

Next

button.

4.

In the

PPP Username and Password

page, enter the PPP username and password that you got

from your ISP.

5.

Select

Dial on Demand

and type in the number for inactivity timeout. The default is 20. Or

select

Always on

.

6.

In the

Configure LAN side Settings

page, type in the IP address and subnet mask for your

LAN. Check

Enable DHCP Server on the LAN

box. And type in the start and end points. Then

type in the leased time that you want. Finally click

Next

. eg.:

Primary IP address:192.168.1.1
Subnet Mask:255.255.255.0
Start IP Address:192.168.1.2
End IP Address: 192.168.1.254

7.

Check the network information. Make sure the settings match the settings provided by ISP.
Click

Finish

.

«
...
65
66
67
68
69
...
»

Summary of Contents for RTA230

























































































Reviews:

No comments

Related manuals for RTA230

Brand: GE Pages: 4

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

Magic WiFi mini Ek

Brand: Devolo Pages: 22

Brand: Patton electronics Pages: 12

Brand: 4G Systems Pages: 2

Brand: Conel Pages: 32

Husky HMG-1648EP

Brand: Ethernet Direct Pages: 16

Brand: Keysight Technologies Pages: 106

Brand: Tripp Lite Pages: 3

JetStream T2600G-28TS

Brand: TP-Link Pages: 1136

Brand: Edgewater Networks Pages: 23

Brand: Juniper Pages: 9

Brand: TP-Link Pages: 2

Brand: Asus Pages: 11

Brand: Asus Pages: 22

Brand: Asus Pages: 2

Brand: Asus Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands