dymax Edge-Carry Page 28 User Manual Download

Page: 28 / 32

Dymax Edge-Carry Conveyor User Guide

Table 9. Troubleshooting Chart for the Edge-Carry Conveyor

Problem

Possible Cause

Testing

Corrective Action

Conveyor Not
Operating

Main Line Circuit
Breaker deployed

Toggle Power Switch off then on
to reset the Circuit Breaker.

Find out why Breaker is deploying.

Improperly fastened
connections

Check all connections.

Properly fasten Power Cord.

Fuses for Motor
Controller blown

Remove Fuses from Fuse Holders
(located in the left side of Control
Box of unit) and check with an
Ohmmeter.

Replace, if defective.

Chain is Too
Loose

Chain is hung up

Inspect the Chain for any signs of
a mechanical bind.

Resolve bind and continue
operation.

Chain tension needs
adjustment

Visually inspect the Chain for
excessive slack.

Loosen the Locknut on the Chain
Tension Adjustment Screw.
Tighten the Chain by turning the
Adjustment Screw. Tighten the
Locknut when adjustment is
complete.

Spare Parts and Accessories

EC-Series Flood Lamp Replacement Parts

Item

Part Number

Lamps

Lamp, Metal Halide 400 Watt UV (Standard)

38560

Lamp, Mercury Vapor 400 Watt UV (Optional)

36970

Lamp, Visible 400 Watt (Optional)

36658

Misc.

Fuse, F 6.25 Amp

35141

Filter, Glass UV (2000-EC Only)

35899

Lamp Base Replacement Kits

35979

Switch, Power

36288

Summary of Contents for Edge-Carry

































Search results

Summary of Contents for Edge-Carry

Reviews:

Related manuals for Edge-Carry

Brands by name

Popular brands

dymax Edge-Carry, User Manual

Search results

Summary of Contents for Edge-Carry

Reviews:

Related manuals for Edge-Carry

Brands by name

Popular brands