background image

 

31 

Dymax Edge-Carry Conveyor User Guide 

Warranty 

From date of purchase, Dymax Corporation offers a one-year warranty against defects in material and 
workmanship on all system components (excluding lamps and Fuses) with proof of purchase and purchase 
date. Unauthorized repair, modification, or improper use of equipment may void your warranty benefits. The 
use of aftermarket replacement parts not supplied or approved by Dymax Corporation will void any effective 
warranties and may result in damage to the equipment. 

IMPORTANT NOTE:

 

DYMAX CORPORATION RESERVES THE RIGHT TO INVALIDATE ANY WARRANTIES, 

EXPRESSED OR IMPLIED, DUE TO ANY REPAIRS PERFORMED OR ATTEMPTED ON DYMAX EQUIPMENT 
WITHOUT WRITTEN AUTHORIZATION FROM DYMAX. THOSE CORRECTIVE ACTIONS LISTED ABOVE ARE LIMITED 
TO THIS AUTHORIZATION.

 

 

Index 

Assembly and Setup, 12 

Belt Speed Adjustment, 18 

Chain Carrier Position Adjustment, 26 

Chain Tension Adjustment, 26 

Conveyor Configurations, 19 

2A, 19 
2B, 19 
Dual Fusion, 20 
Four 5000-EC Lamps, 20 
Single 2000-EC or 1200-EC, 20 
Single Fusion Lamp, 21 

Conveyor Operation, 21 

Systems Using Dymax EC-Series Lamps, 21 
Systems Using Fusion Lamps, 25 

Curing System Safety, 5 

Definition of Terms, 30 

Help, 4 

Maintenance, 26 

Optional Equipment, 

28

 

Parts Included, 12 

Product Description, 7 

Product Overview, 7 

Safety, 4 

Safety of UV Light 

Bright, Visible Light, 6 
High-Temperature Surfaces, 6 
Ozone, 6 
UV Exposure, 5 

Spare Parts and Accessories, 

28

 

Specifications, 8 

Electrical, 8 
General, 8 
Physical, 9 

Support, 4 

Troubleshooting, 27 

Unpacking, 12 

UV Exposure, 5 

UV Light Shielding, 6 

Warranty, 31 

 

Summary of Contents for Edge-Carry

































Reviews: