background image

Valve Mode

This mode adjusts the various characteristics. 

Action Type (ACT)

It can be set to Direct Action (DA) or Reverse Action (RA).

Adjustment of Acting Type (ACT)

1. Press and hold <ENTER> at RUN mode for 6 seconds and AUTO CAL 

message appears.

2. Scroll with <DOWN> until VALVE mode is displayed.
3. Push <ENTER> and ACT RA (in case of Reverse Acting) is displayed.
4. Push <ENTER> and *ACT RA is displayed.
5. Adjust to *ACT DA by pushing <UP> or <DOWN> and save it with <ENTER>. 

+ACT DA message appears.

6. Push <ESC> to exit ACT RA mode.

Characteristics (CHAR)

Set  Characteristics.  There  are  three  types  of  valve  characteristics:  Linear  (LIN),
EQ%  (EQ),  and  Quick  Open  (QO).  The  following  is  the  example  of  the  three
characteristic curves.  

Adjustment of Characteristics (CHAR)

1. To change linear characteristics, scroll with <DOWN> at VALVE menu and select
CHAR LIN (in case of linear characteristics).
2. Push <ENTER>. *HAR LIN mode is displayed and charactertistics can be set to
LIN, EQ, QO or USR.
3. Adjust characteristics (ex: EQ) by pushing <UP> or <DOWN> and save it with
<ENTER>. + HAR EQ is displayed.
4. Push <ESC> to exit CHAR LIN mode. 

User Characteristics (USER SET)

When  a  specific  characteristic  is  needed  but  not  included  in  the  above
characteristics, the user can make a specific characteristic curve by choosing 16
points voluntarily.

Adjustment of User Characteristics (USER SET)

1. Push <ENTER> at VALVE mode and scroll with <DOWN> to select USER SET.
2. Push <ENTER>. *PO SET mode is displayed. In this mode, users can adjust the
first point of characteristic in 16 points. the number on the LCD is the valve stroke
percentage set to P0.
3. Adjust the valve stroke percentage using <UP> or <DOWN>.
4. Save  with  <ENTER>.  While  P0  value  is  being  saved,  *P1  SET  mode  is
displayed.
5. *P1  SET mode  is  used  to  adjust  the  second  point  characteristic  in  16  points.
Adjustment method is the same as P0* SET mode.
6. Continue steps from P2 to P15.
7. After adjusting valve stroke percentage at *P15 SET mode, save with <ENTER>.
8. +SER SET is displayed. All sixteen points of valve stroke percentage are set.
9. Push <ESC> to exit USER SET mode. 

100%

Strok

0

4

20

mA

Quick Open

Linear

EQ%

<ENTER>

6 seconds

<DOWN>

3 times

<ENTER>

<ENTER>

<UP>/<DOWN>

then <ENTER>

<ESC>

3 times

COMPLETED

<ENTER>

6 seconds

<DOWN>

3 times

<ENTER>

<UP>/<DOWN>

then <ENTER>

<ENTER>

<UP>/<DOWN>

then <ENTER>

<ENTER>

<ENTER>

6 seconds

Summary of Contents for PROXIMITY 185 Series











Reviews: