background image

Structure

The structure of the 185 is shown below. The Series 285 structure is the same as
the linear model without the feedback lever. 

Installation

Note: When the positioner is replaced or installed with the actuator, make sure of
the following:
-All inputs and supply pressure to the valve, actuator and other instruments must
be shut down.
-The control valve must be separated from the system with a bypass valve or other
equipment so that the entire system does not shut down.
-No pressure remains in the actuator.

Tools For Installation

• Hexagonal wrenches
• (+) Screw driver
• (-) Screw driver
• Spanners for hexagon head bolts

Series 185 Installation

Series  185  is  used  for  linear  motion  valves  such  as  Dwyer  Instruments’  globe
valves using a spring return type diaphragm actuator or piston actuator. The Series
185  consists  of  the  following  components.  Be  sure  that  all  the  components  are
included. 

1. Series 185 main body
2. Feedback lever and lever spring
3. Flange nut (attached on the bottom of main shaft of Series 185 body)
4. Four hexagon head bolts M8x1.25P
5. Four M8 plate washers

Installing Series 185 with Bracket

It is necessary to make a proper bracket to attach on the actuator yoke. 
The most important considerations in the design of the bracket are as follows:
- Series 185 feedback lever should be at 50% of valve stroke.
-  Feedback  level  connection  bar  of  actuator  clamp  should  be  connected  in  the
position  so  that  the  valve  stroke  and  the  numbers  carved  on  feedback  lever  are
fitted. If the bracket meets the above conditions, Series 185 can be installed very
easily. 

2. Assemble Series 185 and bracket with bolts. Use standard bolts in bolt holes on
the backside of the unit.

Installing Series 185 with Bracket

3. After assembling Series 185 and bracket with bolts, attach it using bolt holes of
actuator yoke. Do not tighten completely, there must be some space. 

4.  Install  bar  connected  with  Series  185’s  feedback  lever  on  the  actuator  clamp.
The  slot  length  between  Series  185’s  feedback  lever  is  .26˝  (6.5  mm),  so  the
diameter of the connection bar should be less than .25˝ (6.3 mm). 

5. Connect the air filter regulator with the actuator temporarily. Set supply pressure
of air filter so that the actuator clamp is positioned at 50% of valve stroke. 

LCD SCREEN

SMART POSITIONER

0

100

50

LCD SCREEN

SMART POSITIONER

Summary of Contents for PROXIMITY 185 Series











Reviews:

Related manuals for PROXIMITY 185 Series